Answer each question completely. Copy and Paste the SPSS output into the word document for the calculations portion of the problems, highlighting correct answers. (Please remember to answer the questions you must interpret the SPSS output). A researcher is interested to learn if there is a linear relationship between the hours in a week spent exercising and a person’s life satisfaction. The researchers collected the following data from a random sample, which included the number of hours spent exercising in a week and a ranking of life satisfaction from 1 to 10 ( 1 being the lowest and 10 the highest).
Participant Hours of Exercis Life Satisfaction
1 3 1
2 14 2
3 14 4
4 14 4
5 3 10
6 5 5
7 10 3
8 11 4
9 8 8
10 7 4
11 6 9
12 11 5
13 6 4
14 11 10
15 8 4
16 15 7
17 8 4
18 8 5
19 10 4
20 5 4
a) Find the mean hours of exercise per week by the participants.
b) Find the variance and standard deviation of the hours of exercise per week by the participants.
c) Run a bivariate correlation to determine if there is a linear relationship between the hours of exercise per week and the life satisfaction. Report the results of the test statistic using correct APA formatting.
d) Run a linear regression on the data. Report the results, using correct APA formatting. Identify the amount of variation in the life satisfaction ranking that is due to the relationship between the hours of exercise per week and the life satisfaction (Hint: the R2 value)
e) Report a model of the linear relationship between the two variables using the regression line formula.

answer:

c. the third graph

part a

answer: a reasonable domain is where n is a real number. so n can be between 0 and 10. both endpoints are included.

work shown:

n is the number of days after the experiment starts. the smallest n can be is n = 0 which means that 0 days have gone by, and we're at the start. to find out how large n should be, then replace f(n) with 16.13 and solve for n. use logarithms to isolate the exponent.

f(n) = 12*(1.03)^n

16.13 = 12*(1.03)^n

16.13/12 = (1.03)^n

1.34416666666667 = (1.03)^n

(1.03)^n = 1.34416666666667

log[ (1.03)^n ] = log[ 1.34416666666667 ]

n*log[ 1.03 ] = log[ 1.34416666666667 ]

n = log[ 1.34416666666667 ]/log[ 1.03 ]

n = 10.0062999823929

this rounds to n = 10 which is fairly close but not 100% perfect. so this is the largest n can be.

note: if you plug n = 10 into f(n), you'll get roughly 16.127 which rounds to 16.13 (this comes up again in part c)

=====================================

part b

answer: the y intercept is 12. it represents the starting height of the plant in cm.

work shown:

plug n = 0 into the f(n) function. simplify

f(n) = 12*(1.03)^n

f(0) = 12*(1.03)^0

f(0) = 12*(1)

f(0) = 12

on day n = 0, aka the starting point, the height f(n) is 12 cm

=====================================

part c

answer: the average rate of change is approximately 0.43061036458991 (round however you need to). this represents the average growth rate from day n = 3 to day n = 10. so the plant grew roughly 0.43 cm per day during this timespan, assuming you round to 2 decimal places.

work shown:

compute f(3)

f(n) = 12*(1.03)^n

f(3) = 12*(1.03)^3

f(3) = 13.112724 < we'll use this later

compute f(10)

f(n) = 12*(1.03)^n

f(10) = 12*(1.03)^10

f(10) = 16.1269965521294 < we'll use this later

now use the formula below with a = 3 and b = 10

aroc = average rate of change

aroc = [ f(b) - f(a) ]/[ b - a ]

aroc = [ f(10) - f(3) ]/[ 10 - 3 ]

aroc = (16.1269965521294 - 13.112724)/(10 - 3)

aroc = 3.0142725521294/7

aroc = 0.43061036458991

round this however you need to

note: the plant grew approximately 3.01 cm over 7 days, so roughly 0.43 cm per day is the average growth rate (if you were to round to 2 decimal places).

option a is correct.

step-by-step explanation:

scale factor: it is used to find proportional measurements.

proportions means having the same ratio.

scale factor is the ratio of the model measurement to the actual measurement in a simplest form.

or we can say that the ratio of any two corresponding lengths in two similar geometric figures

if the scale factor is more than 1, then it is an enlargement,

if the scale factor less than 1, then it is a reduction.

given the two geometric figure:

by definition of proportions, we have

this linear equation would have just one solution.

step-by-step explanation:

the reason why this would have one solution is that it is an expression with just one variable. since that variable is not raised to a power, it will always have just one solution.