Engineering, 25.04.2020 02:59 anyar

A NC drill press is to perform a series of through-hole drilling operations on a 1.75 in thick aluminum plate that is a component in a heat exchanger. Each hole is 3/4 in diameter. There are 100 holes in all, arranged in a 10 by 10 matrix pattern, and the distance between adjacent hole centers (along the square) = 1.5 in. The cutting speed = 300 ft/min, the penetration feed (z-direction) = 0.015 in/rev, and the traverse rate between holes (x-y plane) = 15.0 in/min. Assume that x-y moves are made at a distance of 0.50 in above the work surface, and that this distance must be included in the penetration feed rate for each hole. Also, the rate at which the drill is retracted from each hole is twice the penetration feed rate. The drill has a point angle = 100°. Determine the time required from the beginning of the first hole to the completion of the last hole, assuming the most efficient drilling sequence will be used to accomplish the job.

Answers: 1

Show answers

Answers

Answer from: rireneb

The total time required is $T_{total}= 1601 sec$

Explanation:

From the question we are told that the

The thickness of the aluminium plate is $t = 1.75 \ in$

The diameter of the holes is $d = \frac{3}{4} \ in$

The number holes is n = 100

The pattern they arranged is = 10 by 10 matrix

The distance between the adjacent holes is $D = 1.5 \ in$

The cutting speed $v = 300 \ ft/min =300 *12 = 3600 \ in /min$

The penetration feed is $P = 0.015 \ in / rev$

The traverse rate is $T_r = 15.0 \ in /min$

The distance of the x-y moves $L = 0.50 \ in$

The rate at which the drill id retracted is R = 2P

The point angle of the drill is $\theta = 100^o$

Generally the cutting speed is mathematically represented as

$v = \pi d N$

Where N is the rotational speed

Substituting values

$3600 = \pi * \frac{3}{4} N$

=> $N = \frac{3600}{0.75 * 3.142 }$

$N = 1527.68 rev /min = \frac{1527.68}{60} = 25.46 \ rev /sec$

Now the feed rate is mathematically represented as

$Feed \ Rate [F] = P * N$

Substituting values

F = 0.015 * 25.46

$= 0.3819 \ in$

Next is to obtain the approach distance

The approach distance is mathematically represented as

$a = 0.5 * d * tan (90 - \frac{\theta }{2} )$

substituting values

$a = 0.5 * 0.75 * tan ({90 - \frac{100}{2} })$

$a = 2.5646 \ in$

also we are told that the drill x-y moves is 0.5 in above the work surface

Then the when retracting the drill the total distance moves is

Hence the total drill distance is w = 0.5 + 1.75 + 0.3146

$= 2.5646 \ in$

The time required to drill on hole is

$t_1 = \frac{w }{F }$

Substituting values

$t_1 = \frac{2.56446}{0.3819}$

= 6.71 sce

The retracting rate of the drill would be

K = 2P N

R = 0.015 * 2 * 25.46

= 0.7638

The time required to move the drill out of one hole is

$t_ 2 = \frac{w}{K}$

Substituting value

$t_2 = \frac{2.5646}{0.7638}$

$= 3.3576 \ sec$

The time required to move from one hole to another is

$t_3 = \frac{D}{T_r}$

$= \frac{1.5}{0.25}$

$= 6 \ sec$

The time it would take to perform the drilling of 100 holes is mathematically represented as

t_4 = 100 *t_1

= 6.71 *100

$= 671 \ sec$

Time required for retracting the drill from 100 holes is mathematically represented as

t_5 = 100 * t_2

t_5 = 3.3576 *100

= 336 sec

The time taken to move through the 100 holes is

t_6 = number of travers time * t_3

The number of trans verse time is = 99

t_6 = 99 * 6

$= 594 \ sec$

The time required the drilling task from the beginning of the first hole to the hole is

$T_{total } = t_4 + t_5 + t_6$

= 671 + 336 + 594

$T_{total}= 1601 sec$

Answer from: Quest

Because if a good speech is delivered badly it can bore the audience, confuse them, or make them distrust the speakeri think they all come back to this one, except that last answer because that is false. if your audience starts making fun of you or gets distracted it is because they are either bored, confused or distrust you.

Answer from: Quest

no he didnt use it

explanation:

he said no

Other questions on the subject: Engineering

Engineering, 03.07.2019 15:10, breannaasmith1122

Two flowing streams of argon gas are adiabatically mixed to form a single flow/stream. one stream is 1.5 kg/s at 400 kpa and 200 c while the second stream is 2kg/s at 500 kpa and 100 ? . it is stated that the exit state of the mixed single flow of argon gas is 150 c and 300 kpa. assuming there is no work output or input during the mixing process, does this process violate either the first or the second law or both? explain and state all your assumptions.

Answers: 1

continue

Engineering, 04.07.2019 18:10, mm016281

What difference(s) did you notice using a pneumatic circuit over hydraulic circuit. explain why the pneumatic piston stumbles when it hits an obstacle.

Answers: 2

continue

Engineering, 04.07.2019 18:10, Strick1530

Which of the following components of a pid controlled accumulates the error over time and responds to system error after the error has been accumulated? a)- proportional b)- derivative c)- integral d)- on/off.

Answers: 2

continue

Engineering, 04.07.2019 18:20, xcapo1x

Refrigerant-134a enters the compressor of a refrigerator as superheated vapor at 0.14 mpa and -10°c at a rate of 0.05 ka/s and leaves at 0.8 mpa and 50°c. the refrigerant is cooied in the condenser to 0.72 mpa and 26'c. it is then throttled to 0.15 mpa. sketch the t-s diagram for the system and evaluate: 6) the rate of heat removai from the refrigerated space (kw), it) the power input to the compressor (kw), ii) the isentropic efficiency of the compressor (%), and iv) the cop of the refrigerator.

Answers: 2

continue

You know the right answer?

A NC drill press is to perform a series of through-hole drilling operations on a 1.75 in thick alumi...