Physics, 03.07.2019 05:30 bubbles173883

if you are driving 100 km/h along a straight road and you look to the side for 1.8 s , how far do you travel during this inattentive period?

Answers: 1

Show answers

Other questions on the subject: Physics

Physics, 21.06.2019 23:30, coryowens44

An object starts from rest at point f and speeds up continuously as it moves around an oval. a. choose a point about 1/8 th of the way around the oval from point f, and label it point g. draw a vector to represent the velocity of the object at point g. b. determine the change in velocity vector between points f and g.

Answers: 1

continue

Physics, 22.06.2019 12:50, starr3971

Air is contained in a variable-load piston-cylinder device equipped with a paddle wheel. initially, air is at 400 kpa and 17°c. the paddle wheel is now turned by an external electric motor until 75 kj/kg of work has been transferred to air. during this process, heat is transferred to maintain a constant air temperature while allowing the gas volume to triple. calculate the required amount of heat transfer in kj/kg.

Answers: 2

continue

Physics, 23.06.2019 05:30, geo58

20) what is a magnetic field? 21) in which direction do magnetic field lines always point? 22) sketch a diagram showing how a plotting compass points around a 23) name two magnetic poles that will: a) attract each other b) repel each other. 24) explain why you can use a compass to navigate. 25) what's an electromagnet? 26) list two ways to increase the strength of an electromagnet. 27) the wire in a simple motor feels a force when a current flows through it. why is this? i need answers to check mine

Answers: 1

continue

Physics, 23.06.2019 08:30, 01222002

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28

Answers: 2

continue

You know the right answer?

if you are driving 100 km/h along a straight road and you look to the side for 1.8 s , how far do y...