Physics, 10.04.2022 23:10 joy3449

How does the square of distance between the two changes and the size of the charges affect the electrostatic force

Answers: 1

Show answers

Answers

Answer from: Quest

most voltage drop calculators want the distance between the source and destination. then internally, they double it so both the source and return wires are calculated. but you need to know which distance the calculator uses so you're not half of what you should be or double what you should be.

most circuit breakers will not take a #6 directly, so the electrician will have to splice on a smaller pigtail. you also have to upsize the grounding wire when you upsized the ungrounded (hot) wire (see note in 250.122). this will preclude using most cable assemblies, as a cable with #6 copper will most likely only have a #10 grounding conductor. you need a #6 grounding conductor if the circuit is 20a. a #8 cable is no better, as it will have a #10 grounding conductor too. but most 20a breakers will take a #8 directly.

in your related post, you didn't say what type of load this is. if it is a light or heater, voltage drop won't be a big issue. if this is a motor, the current needs are huge at startup and the voltage drop can pose a problem. if this is a motor, knowing if the motor is under much load during startup will answer the voltage drop effect (a saw is easier to start than a compressor).

Answer from: Quest

what question you dont ask a question

explanation:

Answer from: Quest

force is based upon mass and acceleration.the statement is not always true.

it can be explained from newton's second law of motion.

as per newton's second law of motion the rate of change of momentum is directly proportional to the applied force and takes place along the direction of force.

mathematically it can be written as -

$f\alpha \frac{dp}{dt}$

⇒ $f= k \frac{dp}{dt}$

here k is the proportionality constant whose value is 1.

$f=\frac{dp}{dt}$

$f= \frac{d[mv]}{dt}$

$f= m\frac{dv}{dt} +v\frac{dm}{dt}$

$f=ma+v\frac{dm}{dt}$ [a is the acceleration=dv/dt]

hence we see that force not only depends on mass and acceleration but also on velocity and rate of change of mass. force f will depend on mass and acceleration only when mass is constant.

hence the statement that force is based upon mass and acceleration is false.

Answer from: Quest

ya te mando la respuesta

Other questions on the subject: Physics

Physics, 22.06.2019 19:30, dragador7601

Which of the following compounds would be primarily ionic? methane, ch4, ammonia nh3, calcium chloride, cacl2, or carbon dioxide, co2

Answers: 1

continue

Physics, 23.06.2019 02:00, xbeatdroperzx

Consider an air-filled charged capacitor. how can its capacitance be increased?

Answers: 2

continue

Physics, 23.06.2019 02:40, jackphilander2285

The two metal spheres in the figure are connected by a metal wire with w switch in the middle. initially the switch is open. sphere 1, with the larger radius, i'd given a positive charge. sphere 2, with the smaller radius, is neutral. then the switch is closed. afterward, sphere 1 has charge q1, is at potential v1 and the electric field strength at its surface is e1. the values for sphere 2 are q2, v2, and e2. a. is v1 < ,> , or = to v2? explain. b. is q2 < , > , or = explain? c. is e1 < ,> ,or = to e2? explain?

Answers: 1

continue

Physics, 23.06.2019 03:30, jazzyneen7190

Arock displaces 1.65 l of water. the volume of the rock is: a: 1,650 cm³ b: 165.0 cm³ c: 16.50 cm³ d: 0.165 cm³

Answers: 2

continue

You know the right answer?

How does the square of distance between the two changes and the size of the charges affect the elect...