Answers: 1
Physics, 23.06.2019 01:00, shubbs1038a
First answer marked as brainiest which is the correct equation describing the first law of thermodynamics? a) when the internal energy of a system changes, it equals the amount of heat added plus the work done. b) when work is done by the piston, it is equal to the heat added plus the change in internal energy of the system. c) when heat is added to the system, it is equal to the amount of work done by the piston plus the change in internal energy of the system.
Answers: 2
Physics, 23.06.2019 02:00, solizj6728
Two models of the same compound are shown. in what way is model b better than model a? model b shows the types of elements in the compound, but model a does not. model b shows the three-dimensional shape of the molecule, but model a does not. model b shows how the atoms in the molecule are connected, but model a does not. model b shows the number of atoms of each element in the molecule, but model a does not
Answers: 1
Physics, 23.06.2019 08:30, 01222002
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
Acessna aircraft has a lift-off speed of 120 km/h. what minimum constant acceleration does this requ...
English, 20.04.2021 23:30
Geography, 20.04.2021 23:30
Mathematics, 20.04.2021 23:30
Mathematics, 20.04.2021 23:30
Mathematics, 20.04.2021 23:30