subject
Physics, 01.02.2021 01:00 dianactorres

LAB IS THERMAL ENERGY TRANSFER Directions
Now that the lab is complete, it is time to write your lab report. The purpose of this guide is to help you write a clear and concise report that summarizes the lab you have just completed.
The lab report is composed of four sections:
Section I: Experimental Overview
Provide background information.
Include the hypothesis(es).
Summarize the procedures.

Section II: Data and Observations
Summarize the data you collected in the lab guide.
Include information from data tables.
Include any written observations that are relevant.

Section III: Analysis and Discussion
Discuss any important calculations or formulas used.
Identify key results, what the results indicate, and any trends in the data.
Include graphs (if constructed) that display trends in the data.
Provide possible reasons for any problems with the experiment, or unexpected data.

Section IV: Conclusions
Identify if the hypothesis(es) was (were) supported or refuted.
Provide logical reasoning based on data.
Explain how the experiment could be improved.

To help you write your lab report, you will first answer the questions listed below by reflecting on the experiment you have just completed. Then you will use the answers to these questions to write the lab report that you will turn into your teacher.
You can upload your completed report with the upload tool in formats such as OpenOffice. org, Microsoft Word, or PDF. Alternatively, your teacher may ask you to turn in a paper copy of your report or use a web-based writing tool.
Questions

Section I: Experimental Overview

What is the purpose of the lab, the importance of the topic, and the question you are trying to answer?

it's important because it shows how thermal energy transforms or continues to be all around us in everything

What is your hypothesis (or hypotheses) for this experiment?

What methods are you using to test this (or each) hypothesis?

Section II: Data and Observations
Locate the data and observations collected in your lab guide. What are the key results? How would you best summarize the data to relate your findings?

Do you have quantitative data (numerical results or calculations)? Do you have qualitative data (written observations and descriptions)? How can you organize this date for your report?

Section III: Analysis and Discussion

What do the key results indicate?

If you constructed graphs, what trends do they indicate in your data?

Were there any problems with the experiment or the methods? Did you have any surprising results?

Section IV: Conclusions

What do the results tell you about your hypothesis(es)?

How do the data support your claim above?

If you could repeat the experiment and make it better, what would you do differently and why?

ansver
Answers: 2

Other questions on the subject: Physics

image
Physics, 22.06.2019 10:40, itsyagirl11076
Two point charges are on the y axis. a 3.90-µc charge is located at y = 1.25 cm, and a -2.4-µc charge is located at y = −1.80 cm. (a) find the total electric potential at the origin. v (b) find the total electric potential at the point whose coordinates are (1.50 cm, 0). v
Answers: 1
image
Physics, 22.06.2019 17:30, tray9629
Patricia is trying to compare the average rainfall of new york to that of arizona. a comparison between these two states for the months of july through september would best be measured in
Answers: 3
image
Physics, 22.06.2019 18:20, miner12924owhu4d
Awave with a frequency of 500 hz is traveling at a speed of 100 m/s. what is the wavelength?
Answers: 1
image
Physics, 22.06.2019 19:10, simmonss1185
3. a worker pushes a 30.5 kg polished stone along a polished table with a force on bonin a straight line for 5.20 s after starting from rest. there is no friction between thestone and the table. at the end of the table. the stone is hooked to a cable with a lengthof 62.0 cm to rotate it to a rough table to store until they can be picked up. the roughtable has a coefficient of static friction 0.702 with the polished stone. remember that 8= 9.80 m/s2a) what is the speed of the stone when it is hooked to the cable? b) what is the tension in the cable while the stone is rotating? (there is still nofriction)c) how much force is needed to make the stone begin sliding from rest on therough table? ius = 0.70262.0 cm30.5 kg20.5 kg6= 0
Answers: 2
You know the right answer?
LAB IS THERMAL ENERGY TRANSFER Directions
Now that the lab is complete, it is time to write y...

Questions in other subjects:

Konu
Health, 14.10.2021 22:50
Konu
Mathematics, 14.10.2021 22:50
Konu
Mathematics, 14.10.2021 22:50