subject
Physics, 04.11.2020 08:30 BitFox1684

.com/assignments/3224884884/mydocum ent 9 lesson would be helpful for this part of the test.
2020 Acceleration Test Part #2 (School ID:
Use the graph below to answer the following questions. The initial velocity is 3m/s and the final
velocity is -3m/s. The time at point B, C, and are the three largest digits of your school ID
(from small to large). BC), CI ,DE)
A
O
D
a. Fill the table below. (H18 points)
A to B
B to C
C to D
Motion direction
Motion type
Displacement
Acceleration
b. The overall displacement (12 points)
c. The average velocity ( 2 points)
d. The overall distance: 12 points)
e. The average speed: (2 points)

ansver
Answers: 1

Other questions on the subject: Physics

image
Physics, 22.06.2019 05:30, ygrant03
Debbie places two shopping carts in a cart corral she pushes the first cart which then pushes a second cart what force is being exerted
Answers: 1
image
Physics, 23.06.2019 01:20, juli8350
What is the state of matter with a specific volume but no definite shape
Answers: 1
image
Physics, 23.06.2019 05:20, leahstubbs
Derive the formula 2as=v² -u² where the formula have have usual meanings
Answers: 1
image
Physics, 23.06.2019 08:30, 01222002
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
You know the right answer?
.com/assignments/3224884884/mydocum ent 9 lesson would be helpful for this part of the test.
...

Questions in other subjects:

Konu
Arts, 07.10.2019 18:00