Physics, 22.10.2020 16:01 audreymvarney

PART II – CHOOSING THE APPROPRIATE UNIT For each example below choose the appropriate unit to measure each (mm, cm, m or km). 1. Width of physics book 2. Distance from New York to Utah 3. Length of fingernail 4. Length of hallway 5. Height of a mountain 6. Length of a fork 7. Distance between cities 8. Width of your eyeball

Answers: 1

Show answers

Other questions on the subject: Physics

Physics, 21.06.2019 20:40, cuavang55

In a steady-flow steam power plant system, two adiabatic high-pressure and low-pressure turbines ane used to generate power. superheated steam enters the high-pressure turbine at 8 mpa and 550°c. the steam expands in the high-pressure turbine to a saturated vapor at 3 mpa. in order to increase the powe generation of the power plant, another steam turbine working in a lower pressure ranges is deployed. the outlet vapor from the first turbine is heated up at a boiler to the temperature of 500 c at the constant pressure of first turbine's outlet (3 mpa). then, the vapor enters the second turbine and produces extra work. the exit conditions of the second turbine are 5o kpa and 90 percent quality. if the total power output of the power plant is 25 mw, determine a) the mass flow rate of the water (kg/s). b) heat transfer rate in the boiler (mw). (30 points) 3 mpa 00 c 8 mpa s0 c high pres turbine low pres boiler turbine 50 kpa 3 mpa 09 saturated vapor t heat engine, shown in the figure, operates between high temperature and low temperature of through a heat 4. a carnot tn and tu respectively. this heat engine receives energy from a heat reservoir at t exchanger where the heat transferred is proportional to the temperature difference as ? = k (z,-7, ). it rejects heat at a given low temperature tl. to design the heat engine for maximum work output, find the high temperature, th, as a function of tes and t. (15 points) qe

Answers: 3

continue

Physics, 22.06.2019 00:30, Solany6426

Part f - example: finding two forces (part i) two dimensional dynamics often involves solving for two unknown quantities in two separate equations describing the total force. the block in (figure 1) has a mass m=10kg and is being pulled by a force f on a table with coefficient of static friction îľs=0.3. four forces act on it: the applied force f (directed î¸=30â above the horizontal). the force of gravity fg=mg (directly down, where g=9.8m/s2). the normal force n (directly up). the force of static friction fs (directly left, opposing any potential motion). if we want to find the size of the force necessary to just barely overcome static friction (in which case fs=îľsn), we use the condition that the sum of the forces in both directions must be 0. using some basic trigonometry, we can write this condition out for the forces in both the horizontal and vertical directions, respectively, as: fcosî¸â’îľsn=0 fsinî¸+nâ’mg=0 in order to find the magnitude of force f, we have to solve a system of two equations with both f and the normal force n unknown. use the methods we have learned to find an expression for f in terms of m, g, î¸, and îľs (no n).

Answers: 2

continue

Physics, 22.06.2019 15:30, lexiepedit4958

The movement of electrons between atoms is called an

Answers: 2

continue

Physics, 22.06.2019 22:30, gokusupersaiyan12345

Find v1, the speed of the fluid in the left end of the main pipe. express your answer in terms of h1, h2, g, and either a1 and a2 or γ, which is equal to a1a2.

Answers: 2

continue

You know the right answer?

PART II – CHOOSING THE APPROPRIATE UNIT For each example below choose the appropriate unit to measur...