Physics, 03.06.2020 22:58 OlamideO3

Difference between preventive and corrective maintenance

Answers: 3

Show answers

Answers

Answer from: dijaflame67

Preventive: reduces overall maintenance costs

corrective: preformed after a malfunction

Explanation:

Preventive maintenance, when well planned, can reduce overall maintenance costs and increase the productivity of equipment and installations in a comprehensive manner. As many will know, corrective maintenance is usually performed after a malfunction or failure occurs in the equipment.

Answer from: kayltosh2729

Preventive maintenance, when well planned, can comprehensively reduce the overall maintenance costs and increase the productivity of equipment and facilities.

As many will know, corrective maintenance is usually performed after the occurrence of a malfunction or failure in a equipment.

Explanation:

Corrective maintenance:

Corrective maintenance is carried out after fault recognition with the intention of returning an item to a state in which it can perform a required function. Maintenance interventions include emergency repairs, as well as unscheduled repairs based on inspection or customer complaints.

It has been estimated that corrective maintenance can cost three times more than the same repairs done under a preventative maintenance regime.

Preventative maintenance

Preventative Maintenance comprises the replacement of components or overhauling of assets at a fixed interval. The aim is to avoid expensive repair and corrective activities resulting from premature equipment damage or failure, and that lead to unscheduled downtime.

In most cases, this approach takes the form of time-driven tasks performed to maintain a level of availability and reliability, but it may also be triggered by monitoring conditions.

Interval-based preventative maintenance is carried out in accordance with an established time schedule or number of units of use and can be guided by supplier manuals or experience.

Condition-based preventative maintenance involves inspection of assets. Testing and parameter monitoring can be applied to determine maintenance needs and requirements.

I hope it helps

Answer from: Quest

i would say the answer is food.

hope this !

Answer from: Quest

answer: a) y=-8x+5

a) m= -8

b) m= -2

c) m= 7

d) m= 6

Other questions on the subject: Physics

Physics, 21.06.2019 19:30, BePaige

Act has a 1200: 5 or 240: 1 turns ratio. it is short circuited. what is the maximum current at 1200a primary if we put a 100ohm resistor across the secondary end of the ct. use it as current source circuit.

Answers: 2

continue

Physics, 22.06.2019 10:00, lorelei7668

(a) calculate the number of electrons in a small, electrically neutral silver pin that has a mass of 10.0 g. silver has 47 electrons per atom, and its molar mass is 107.87 g/mol. (b) imagine adding electrons to the pin until the negative charge has the very large value 1.00 mc. how many electrons are added for every 109 electrons already present

Answers: 3

continue

Physics, 22.06.2019 14:10, momo842

Your starship, the aimless wanderer, lands on the mysterious planet mongo. as chief scientist-engineer, you make the following measurements: a 2.50-kg stone thrown upward from the ground at 14.0 m/s returns to the ground in 5.70 s ; the circumference of mongo at the equator is 2.20×10^5 km ; and there is no appreciable atmosphere on mongo. (a) the starship commander, captain confusion, asks for the following information: what is the mass of mongo? (b) if the aimless wanderer goes into a circular orbit 2.20×10^4 km above the surface of mongo, how many hours will it take the ship to complete one orbit? (c) an unmanned spacecraft is in a circular orbit around the moon, observing the lunar surface from an altitude of 44.0 km . to the dismay of scientists on earth, an electrical fault causes an on-board thruster to fire, decreasing the speed of the spacecraft by 23.0 m/s . if nothing is done to correct its orbit, with what speed (in km/h) will the spacecraft crash into the lunar surface?

Answers: 1

continue

Physics, 23.06.2019 00:10, alisonnn101

During cooling, the kinetic energy of the molecules falls. why does this happen? a. the motion of the molecules increases. b. the motion of the molecules slows down. c. the van der waals forces between molecules decrease d. the forces of attraction between the molecules are overcome.

Answers: 2

continue

You know the right answer?

Difference between preventive and corrective maintenance...