Physics, 13.02.2020 22:19 alisonlebron15

is the relative long-distance movement from one region of a country to another.

a. Regional mobility
b. Intraregional migration
c. International mobility
d. Forced migration
e. Interregional migration

Answers: 3

Show answers

Other questions on the subject: Physics

Physics, 22.06.2019 16:50, Walkman2092

Calculate the first and second velocities of the car with four washers attached to the pulley, using the formulas v1 = 0.25 m / t1 , and v2 = 0.25 m / (t2 – t1) where t1 and t2 are the average times the car took to reach the 0.25 and the 0.50 meter marks. record these velocities, to two decimal places, in table e.

Answers: 2

continue

Physics, 22.06.2019 22:20, queenbee2994

One hazard of space travel is debris left by previous missions. there are several thousand masses large enough to detect by radar orbiting the earth, but there are far greater numbers of very small masses such as flakes of paint. calculate the force exerted by a 0.110 mg chip of paint that strikes a space shuttle window at a relative speed of 5.00 ✕ 103 m/s and sticks, given the collision lasts 6.00 ✕ 10-8 s. such a collision chipped the window of the ill-fated challenger in june 1983, causing $50,000 of damage.

Answers: 2

continue

Physics, 23.06.2019 06:30, jaallen3679

Two blocks of aluminum (specific heat c=0.22 cal/g celsius) with masses of 1000 g and 100 g are at a temperature of 70 c. which block has more thermal (internal) energy? explain why?

Answers: 2

continue

Physics, 23.06.2019 08:30, 01222002

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28

Answers: 2

continue

You know the right answer?

is the relative long-distance movement from one region of a country to another.

a. Regio...