Physics, 29.10.2019 06:31 Shami7457

A9.6 cm diameter circular loop of wire is in a 1.10 t magnetic field perpendicular to the plane of the loop. the loop is removed from the field in 0.15 s what is the average induced emf? draw the loop and field and indicate the direction of the induced current

Answers: 3

Show answers

Answers

Answer from: miguegen6225

Thus induced emf is 0.0531 V

Solution:

As per the question:

Diameter of the loop, $d = 9.6\ cm = 0.096\ m$

Thus the radius of the loop, R = 0.048 m

Time in which the loop is removed, t = 0.15 s

Magnetic field, B = 1.10 T

Now,

The average induced emf, e is given by Lenz Law:

$e = - \frac{\Delta \phi_{B}}{\Delta t}$

where

$\phi_{B}$ = magnetic flux = $A\Delta B$

where

A = cross sectional area

Also, we know that:

$e = - \frac{A\Delta B}{\Delta t}$

$e = - \frac{\pi r^{2}\times (0 - 1.10)}{0.15}$

$e = - \frac{\pi \times 0.048^{2}\times (0 - 1.10)}{0.15}$

e = 0.0531 V

The sketch is shown in the figure, where I indicates the direction of the induced current.

A9.6 cm diameter circular loop of wire is in a 1.10 t magnetic field perpendicular to the plane of t

Answer from: artiomtyler007

emf=0.531 V

Explanation:

Induced EMF is equals to the change in the Magnetic flux per unit change in time.

It is calculated by the Faraday's law which is given mathematically as:

$emf=N \times \frac{\Delta (B.A) }{\Delta t}$ ..................................(1)

where:

N= number of turns in looped coil of wireB= magnetic fieldA= area of the loop formed by the wiret= change in time $\Delta$ = change in the quantity from initial to final state.

Given:

N=1 (since it is a loop not a coil of loops)

Diameter of loop, d = 9.6 cm

B = 1.10 T

${\Delta t}$ = 0.15 s

Firstly, we find the area of loop:

$A= \pi \frac{d^{2}}{4}$

$A= \pi \frac{(9.6 \times 10^{-2} )^{2}}{4}$

$A= 7.2382 \times 10^{-3} m^{2}$

Putting respective values in eq. (1)

$emf=1\times \frac{\Delta (1.10\times 7.2382 \times 10^{-3}) }{0.15}$

emf=0.531 V

THe direction of the induced emf is in accordance with the Lenz Law which states that the direction of an induced current is always such as to oppose the cause by which it is produced.

Answer from: Quest

this could be newton#'s law of cooling. the cooling curve is exponential

Answer from: Quest

answer

procedural programming, object-oriented programming

explanation

procedural programming is a type of computer programming language that specifies a series of well structured steps and procedures within its development period of time. it contains a systematic order of statements, functions and commands to complete a computational task or program. it is centered on creating procedures. while object oriented programming is a programming language that is centered on creating objects rather that actions and data rather than logic.. it has four principles which are inheritance, polymorphism, abstraction and encapsulation

Other questions on the subject: Physics

Physics, 21.06.2019 22:00, markyyy53

Aroll in a paper machine is powered by a separately excited dc machine. operating point 1 (under load): the roll typically operates at 764 rpm and must provide 301 nm of torque to oppose the load of the paper. the armature voltage is 230v for this operating point operating point 2 (no load): when the load is removed the speed of the roll increases to 900 rpm (the field characteristics are unchanged) la ea dev m (a) calculate the maximum torque (units of nm) that the motor can supply with this applied voltage (b) calculate the value of the armature resistance, ra (in ohms) (c) at operating point 1 (loaded condition), the field current, i, and the total input power (armature field), are measured to be to be 10 a and 28,600 w respectively. use this information to calculate the value of the field resistance, rf (in ohms). (d) (d) at operating point 1 (loaded condition), calculate the motor efficiency. express your answer as a percent to at least 2 significant digits. (d) if the field voltage is reduced by 1/2, calculate the new stall torque (in nm) of the motor (f). if the field voltage is reduced by 1/2, calculate the new no-load speed (in rad/sec)

Answers: 1

continue

Physics, 22.06.2019 00:00, sydneydavis57

Jackson is designing a new heater, and he wants to experiment with different thermally conductive materials. which of these materials would be useful in conducting heat?

Answers: 1

continue

Physics, 22.06.2019 05:40, izzyisawesome5232

An ideal polarizer with its transmission axis rotated 30 degrees to the vertical is placed in a beam of unpolarized light of intensity 10w/m^2. after passing through the polarizer, what is the intensity of the beam? a. 8.7 w/m^2 b. 7.5 w/m^2 c. 5.0 w/m^2 d. 10 w/m^2 e. 2.5 w/m^2

Answers: 1

continue

Physics, 22.06.2019 10:00, autumnskye1

In a heat engine if 1000 j of heat enters the system the piston does 500 j of work, what is the final internal energy of the system if the initial energy was 2000 j? 1. write the equation 2.list out your known variables 3.plug the numbers into the equations 4.solve 5.write your solution statement that includes initial energy and final

Answers: 3

continue

You know the right answer?

A9.6 cm diameter circular loop of wire is in a 1.10 t magnetic field perpendicular to the plane of t...