In the daytona 500 auto race, a ford thunderbird and a mercedes benz are moving side by side down a straightaway at 78.5 m/s. the driver of the thunderbird realizes that she must make a pit stop, and she smoothly slows to a stop over a distance of 250 m. she spends 5.00 s in the pit and then accelerates out, reaching her previous speed of 78.5 m/s after a distance of 370 m. at this point how far has the thunderbird fallen behind the mercedes benz, which has continued at a constant speed?

FT is 1020.6 meters (1640.6 meters - 620 meters) far from MB

Explanation:

First you have to consider that the Ford Thunderbird (FT) follows a rectilinear motion with varying acceleration, while Mercedez Benz (MB) has a constant velocity (no acceleration). So if you finde the time spent by FT in each section, and the distance, then you will find the distance for MB.

1) Vf² = Vi² + 2ad, where Vf: final velocity, Vi: ionitial velocity, a: acceleration and d: distance.

For the first portion  (0 m/s)² = (78.5 m/s)² + 2a(250 m) ⇒

-(78.5 m/s)² / 2(250m) = a ⇒ a = -12.3 m/s².

Now, you can find the corresponding time for this section with the following formule: Vf = Vi + at ⇒ 0 m/s = 78.5 m/s + (-12.3 m/s²) t

⇒ t= (-78.5 m/s)/ (-12.3 m/s²) ⇒ t= 6.4 seconds.

2) Then FT spent 5 seconds in the pit.

3) The the FT accelerates until reach 78.5 m/s again in a distance of 370 m.

Vf² = Vi² + 2ad ⇒ (78.5 m/s)² = (0 m/s)² + 2a(370 m)

⇒ (78.5 m/s)²/ 2(370 m) = a ⇒ a = 8.3 m/s²

Then, Vf = Vi + at ⇒ 78.5 m/s = 0 m/2 + (8.3 m/s²) t

⇒ (78.5 m/s)/(8.3 m/s²) = t ⇒ t = 9.5 seconds.

4) Summarizing, the FT moves 620 meters (250 + 370 mts) in 20.9 seconds ( 6.4 s + 5 s + 9.5 s).

5) During this time, MB moves

Velocity = distance/ time ⇒ Velocity x time = Distance

⇒ Distance = (78.5 m/s) x  (20.9 seconds) ⇒ Distance = 1640.6 meters

6) Finally, the FT is 1020.6 meters (1640.6 meters - 620 meters) far from MB

most voltage drop calculators want the distance between the source and destination. then internally, they double it so both the source and return wires are calculated. but you need to know which distance the calculator uses so you're not half of what you should be or double what you should be.

most circuit breakers will not take a #6 directly, so the electrician will have to splice on a smaller pigtail. you also have to upsize the grounding wire when you upsized the ungrounded (hot) wire (see note in 250.122). this will preclude using most cable assemblies, as a cable with #6 copper will most likely only have a #10 grounding conductor. you need a #6 grounding conductor if the circuit is 20a. a #8 cable is no better, as it will have a #10 grounding conductor too. but most 20a breakers will take a #8 directly.

in your related post, you didn't say what type of load this is. if it is a light or heater, voltage drop won't be a big issue. if this is a motor, the current needs are huge at startup and the voltage drop can pose a problem. if this is a motor, knowing if the motor is under much load during startup will answer the voltage drop effect (a saw is easier to start than a compressor).

answercollision;