subject

Mathematics, 25.06.2019 20:30 toledanomariap43bxm

May someone ? i'll give out a lot of points. 1. find the length of side b to two decimal places. 2. find the length of side a to two decimal places.

May someone ? i'll give out a lot of points. 1. find the length of side b to two decimal places. 2

ansver

Answers: 1

Show answers

Other questions on the subject: Mathematics

Mathematics, 21.06.2019 14:00, layahmonaee

Which unit of measure would be the most appropriate to measure the capacity of a bottle of nail polish? a. fluid ounces b. cups c. pints d. quarts e. gallons

Answers: 1

Mathematics, 21.06.2019 19:00, Madsissabell

1) in triangle the, what is the measure of angle t (in degrees)? 2) in triangle bat, the measure of angle b is 66∘, and the measure of angle t is 77∘.what is the measure of the exterior angle at a (in degrees)?

Answers: 1

Mathematics, 21.06.2019 19:50, twitter505567

How do i simply this expression (quadratic formula basis) on a ti-84 or normal calculator?

Answers: 3

Mathematics, 21.06.2019 21:30, drepeter86

50 people men and women were asked if they watched at least one sport on tv. 20 of the people surveyed are women, but only 9 of them watch at least one sport on tv. 16 of the men watch at least one sport on tv. make a a two-way table and a relative frequency table to represent the data.

Answers: 3

You know the right answer?

May someone ? i'll give out a lot of points. 1. find the length of side b to two decimal places. 2...

Questions in other subjects:

Konu

Engineering, 26.07.2019 16:20

The diesel cycle is very close to the otto cycle. what is a difference between the two air-standard cycles? a)-the diesel cycle assumes constant volume heat rejection and otto cyc...

Konu

Engineering, 26.07.2019 16:20

One can expect the velocity boundary layer for laminar flow to be much thicker than the thermal boundary layer when the prandtl number is a. > > 1 b. < < 1 c. = 1...

Konu

Engineering, 26.07.2019 16:20

Select a light w shape for a column subjected to an axial compressive load of 355 kips. the unbraced length of column is 16 ft and the ends are pinned. use a36 grade steel....

Konu

Engineering, 26.07.2019 16:20

Which has more threads per inch: ¼-20 or an m8-1? a)- ¼-20 b)- м8-1 c)- same...

Konu

Engineering, 26.07.2019 16:20

Use the map of ohio that follows to find the average wind speed for columbus, ohio (5.5 m/s). a wind turbine located at byers mazda subaru near i 270 on the north part of columbus...

Konu

Engineering, 26.07.2019 16:20

An a36 - 1.0 inch diameter steel tie rod is used to support a tensile load of 12,000 lb. determine the stress in the tie rod and calculate the factor of safety....

Konu

Engineering, 26.07.2019 16:20

Afluid in direct contact direct contact with a stationary solid surface will have a velocity of zero in accordance with the condition. a. no-slip b. temperature-jump c. stagnation...

Konu

Engineering, 26.07.2019 16:20

Steam enters an adiabatic turbine at 10 mpa and 500 °c and leaves at 30 kpa with a quality of 90 percent. neglecting the changes in kinetic and potential energies, determine the ma...

Konu

Engineering, 26.07.2019 16:20

Calculate the bending stress in a 1 ¾ in. x 12 in. x 18 ft. microllam lvl beam under the following load conditions: a)-2500 lb concentrated load at center with the beam fixed at b...

Konu

Engineering, 26.07.2019 16:20

A) what is a free-cutting steel? explain. b) show the free energy vs. composition curve (schematic) for an alloy system a-b where there is a strong tendency for long range orderin...

More questions: Mathematics Another questions