![subject](/tpl/images/cats/User.png)
Engineering, 25.11.2021 07:50 xojade
Automotive batteries are an example of which hazard class
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Other questions on the subject: Engineering
![image](/tpl/images/cats/User.png)
Engineering, 03.07.2019 15:10, EmilySerna
Heat is added to a piston-cylinder device filled with 2 kg of air to raise its temperature 400 c from an initial temperature of t1 27 cand pressure of pi 1 mpa. the process is isobaric process. find a)-the final pressure p2 b)-the heat transfer to the air.
Answers: 1
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, skpdancer1605
Ariver flows from north to south at 8 km/h. a boat is to cross this river from west to east at a speed of 20 km/h (speed of the boat with respect to the earth/ground). at what angle (in degrees) must the boat be pointed upstream such that it will proceed directly across the river (hint: find the speed of the boat with respect to water/river)? a 288 b. 21.8 c. 326 d. 30.2
Answers: 3
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, michellerosas
Ajournal bearing has a journal diameter of 3.250 in with a unilateral tolerance of 20.003 in. the bushing bore has a diameter of 3.256 in and a unilateral tolerance of 0.004 in. the bushing is 2.8 in long and supports a 700-lbf load. the journal speed is 900 rev/min. find the minimum oil film thickness and the maximum film pressure for both sae 20 and sae 20w-30 lubricants, for the tightest assembly if the operating film temperature is 160°f. a computer code is appropriate for solving this problem.
Answers: 3
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, 0436500
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
You know the right answer?
Automotive batteries are an example of which hazard class...
Questions in other subjects:
![Konu](/tpl/images/cats/en.png)
English, 22.09.2019 16:20
![Konu](/tpl/images/cats/biologiya.png)
Biology, 22.09.2019 16:20
![Konu](/tpl/images/cats/geografiya.png)
Geography, 22.09.2019 16:20
![Konu](/tpl/images/cats/ekonomika.png)
![Konu](/tpl/images/cats/mat.png)
Mathematics, 22.09.2019 16:20
![Konu](/tpl/images/cats/istoriya.png)
![Konu](/tpl/images/cats/en.png)
![Konu](/tpl/images/cats/istoriya.png)
History, 22.09.2019 16:20
![Konu](/tpl/images/cats/istoriya.png)
![Konu](/tpl/images/cats/mat.png)
Mathematics, 22.09.2019 16:20