Engineering, 17.04.2021 19:10 maelaysiap

Two HVAC/R technicians are discussing the soldering of copper pipes. Technician A says that when soldering, it's important to apply flux all the way to the end of the pipe. Technician B says that when soldering, you should twist the pipe inside the fitting to help spread the flux around the joint area. Which one of the following statements is correct?

Answers: 1

Show answers

Answers

Answer from: alexandriacatro9419

Explanation:

Read the passage carefully and then answer the question.

I have in my hand two publications; one is The Adventures of William Dodd the Factory Cripple and the other is entitled The Factory System - both books have gone forth to the public under the sanction of the noble Lord Ashley. I do not wish to go into the particulars of the character of this man, for it is not necessary to my case, but I can demonstrate, that his books and statements are wholly unworthy of credit. Dodd states that from the hardships he endured in a factory, he was "done up" at the age of thirty-two, whereas I can prove that he was treated with uniform kindness, which he repaid by gross immorality of conduct, and for which he was discharged from his employment.

How does the speaker seem to feel about William Dodd?

He feels that William Dodd is a liar who should be questioned.

He feels that William Dodd is a good person who would never lie.

He feels that William Dodd is a dangerous and unstable individual.

He feels that William Dodd is a man who needs help from others.

Answer from: skylar1315

B is correct

Explanation:

Answer from: Quest

the equation above shows how temperature f, measured in degrees fahrenheit, relates to a temperature c, measured in degrees celsius. based on the equation, which of the following must be true?

a temperature increase of 1 degree fahrenheit is equivalent to a temperature increase of

degree celsius.

a temperature increase of 1 degree celsius is equivalent to a temperature increase of 1.8 degrees fahrenheit.

a temperature increase of

degree fahrenheit is equivalent to a temperature increase of 1 degree celsius.

a) i only

b) ii only

c) iii only

d) i and ii only

Answer from: Quest

answer:

yes that is right have a good day

Other questions on the subject: Engineering

Engineering, 03.07.2019 14:10, bryneosburn

Line joining liquid phase with liquid and solid phase mixture is known as: a) liquidus b) solidus c) tie line d) none of the mentioned

Answers: 2

continue

Engineering, 04.07.2019 18:10, mm016281

What difference(s) did you notice using a pneumatic circuit over hydraulic circuit. explain why the pneumatic piston stumbles when it hits an obstacle.

Answers: 2

continue

Engineering, 04.07.2019 18:20, jessie8022

Apiston-cylinder device contains 0.1 m3 of liquid water and 0.9 m3 of water vapor in equilibrium at 800 kpa. heat is transferred at constant pressure until the temperature of water reaches 350 °c. determine (a) the quality of water at the initial state (b) the work associated with this process, (c) the heat associated with this process.

Answers: 2

continue

Engineering, 04.07.2019 19:20, holaadios222lol

Apiping systems consists of 6 m of 6-std type k and 12 m of 4-std type k, both drawn copper tubing. the system conveys ethylene glycol at a rate of 0.013 m3/s. the pressure drop across the system is to be calculated. there are two 90° elbows in the 6-in pipe, a reduction from the 6-in pipe to the 4-in pipe and four 90° elbows in the 4-in pipe. all fittings are soldered (same as flanged) and regular. the inlet and outlet of the system are at the same height.

Answers: 1

continue

You know the right answer?

Two HVAC/R technicians are discussing the soldering of copper pipes. Technician A says that when sol...