subject
Engineering, 06.02.2021 01:40 kimryan520

El señor Juan José Bolaños retiró sus cesantías para arreglos locativos de un local en la plaza de Abastos en Bogotá le giraron la suma de 15 millones de pesos y va disponer para los arreglos del local el 65% del dinero retirado , el
local tiene las siguientes dimensiones 6m por 25m y una altura de 4m..
La remodelación contempla el cambio total del piso, colocar baldosa en cada una de las paredes hasta los 3/4
de la altura y pintar lo restante, además de esto debe cambiar el tejado.
El local cuenta con una reja puerta de entrada que mide 2.5 m por 3m, 4 ventanas cuadradas de 1.6 m de
largo un baño de 2 m por 1.5 m al fondo del local
Las canecas de pintura lavable por 10 litros alcanzan para pintar 5 a 6 m2
Don Juan José nos solicita realizar dos presupuestos de compra y nos paga el 10% por el mas alto y 15% por
el de menor valor y así poder realizar las compras y contratar para la adecuación del local.

.
MATERIAL DE APOYO
En la siguiente tabla encuentras información de algunos materiales y precios a su elección.
MATERIAL MEDIDAS PRECIO
Baldosa Guadalupe 33 cm x 33 cm $ 25.000 m2
Baldosa Cristo Rey 45 cm x 45 cm $ 37.000 m2
Baldosa La Popa 30 cm x 25 cm $ 21.000 m2
Baldosa pared Bogotá 20 cm x 25 cm $ 25.000 m2
Baldosa pared Cali 35 cm x 25 cm $ 29.000 m2
Baldosa pared Cartagena 20 cm x 22 cm $ 27.000 m2
Pintura puertas y rejas, caneca con rendimiento 2m2 por $25.000
Teja Vivanco 120 cm x 220 cm $ 47.000 m2
Teja Albaricoque 130 cm x 250 cm $ 54.000 m2
Pintura lavable A 5m2 $ 114.000
Pintura lavable B 6m2 $ 132.000

ansver
Answers: 3

Other questions on the subject: Engineering

image
Engineering, 03.07.2019 14:10, cowgyrlup124
Explain the difference laminar and turbulent flow. explain it with the shear stress and the velocity profiles.
Answers: 1
image
Engineering, 03.07.2019 14:10, kayabwaller4589
When at a point two solid phase changes to one solid phase on cooling then it is known as a) eutectoid point b) eutectic point c) peritectic point d) peritectoid point
Answers: 3
image
Engineering, 04.07.2019 18:10, koolgurl2003
Apump is used to circulate hot water in a home heating system. water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. the inlet pressure and temperature are 14.7 lbf/in.2, and 180°f, respectively; at the exit the pressure is 60 lbf/in.2 the pump requires 1/15 hp of power input. water can be modeled as an incompressible substance with constant density of 60.58 lb/ft3 and constant specific heat of 1 btu/lb or. neglecting kinetic and potential energy effects, determine the temperature change, in °r, as the water flows through the pump.
Answers: 1
image
Engineering, 04.07.2019 18:10, keigleyhannah30
Aplate clutch has a single pair of mating friction surfaces 250-mm od by 175-mm id. the mean value of the coefficient of friction is 0.30, and the actuating force is 4 kn. a) find the maximum pressure and the torque capacity using the uniform-wear model. b) find the maximum pressure and the torque capacity using the uniform-pressure model.
Answers: 3
You know the right answer?
El señor Juan José Bolaños retiró sus cesantías para arreglos locativos de un local en la plaza de A...

Questions in other subjects:

Konu
Mathematics, 11.02.2020 02:28