![subject](/tpl/images/cats/User.png)
Engineering, 24.10.2020 21:50 DaylaReevaFEEVA2757
Identify the five protective factors
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Other questions on the subject: Engineering
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 16:10, TheOriginalMeyah
An electrical motor raises a 50kg load at a construct velencity .calculate the power of the motor, if it takes 40sec to raise the load through a height of 24m(take g =9.8n/g)
Answers: 2
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, ahmedeldyame
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, koolgurl2003
Apump is used to circulate hot water in a home heating system. water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. the inlet pressure and temperature are 14.7 lbf/in.2, and 180°f, respectively; at the exit the pressure is 60 lbf/in.2 the pump requires 1/15 hp of power input. water can be modeled as an incompressible substance with constant density of 60.58 lb/ft3 and constant specific heat of 1 btu/lb or. neglecting kinetic and potential energy effects, determine the temperature change, in °r, as the water flows through the pump.
Answers: 1
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, keigleyhannah30
Aplate clutch has a single pair of mating friction surfaces 250-mm od by 175-mm id. the mean value of the coefficient of friction is 0.30, and the actuating force is 4 kn. a) find the maximum pressure and the torque capacity using the uniform-wear model. b) find the maximum pressure and the torque capacity using the uniform-pressure model.
Answers: 3
You know the right answer?
Identify the five protective factors...
Questions in other subjects:
![Konu](/tpl/images/cats/geografiya.png)
Geography, 28.08.2019 23:00
![Konu](/tpl/images/cats/en.png)
![Konu](/tpl/images/cats/mat.png)
Mathematics, 28.08.2019 23:00
![Konu](/tpl/images/cats/mat.png)
Mathematics, 28.08.2019 23:00
![Konu](/tpl/images/cats/en.png)
English, 28.08.2019 23:00
![Konu](/tpl/images/cats/istoriya.png)
History, 28.08.2019 23:00
![Konu](/tpl/images/cats/health.png)
Health, 28.08.2019 23:00
![Konu](/tpl/images/cats/biologiya.png)
![Konu](/tpl/images/cats/health.png)
Health, 28.08.2019 23:00
![Konu](/tpl/images/cats/fizika.png)
Physics, 28.08.2019 23:00