Engineering, 21.10.2020 16:01 kaleighashtyn

A 30-mm-diameter shaft, made of AISI 1018 HR steel, transmits 10 kW of power while rotating at 200 rev/min. Assume any bending moments present in the shaft to be negligibly small compared to the torque. Determine the static factor of safety based on:a) The maximum-shear-stress failure theory. b) The distortion-energy failure theory.

Answers: 2

Show answers

Answers

Answer from: eks8252

a) According to the maximum-shear-stress failure theory, the static factor of safety of the shaft is 2.440.

b) According to the distortion-energy failure theory, the static factor of safety of the shaft is 2.816.

Explanation:

First, we need to determine the torque experimented by the shaft (), measured in kilonewton-meters, whose formula is described:

$T = \frac{\dot W}{\omega}$ (Eq. 1)

Where:

$\dot W$ - Power, measured in kilowatts.

$\omega$ - Angular velocity, measured in radians per second.

If we know that $\dot W = 10\,kW$ and $\omega = 20.944\,\frac{rad}{s}$ , then the torque experimented by the shaft:

$T = \frac{10\,kW}{20.944\,\frac{rad}{s} }$

$T =0.478\,kN\cdot m$

Let consider that shaft has a circular form, such that shear stress is determined by the following formula:

$\tau = \frac{16\cdot T}{\pi\cdot D^{3}}$ (Eq. 2)

Where:

- Diameter of the shaft, measured in meters.

$\tau$ - Torsional shear stress, measured in kilopascals.

If we know that $D = 0.03\,m$ and $T =0.478\,kN\cdot m$ , the torsional shear stress is:

$\tau = \frac{16\cdot (0.478\,kN\cdot m)}{\pi\cdot (0.03\,m)^{3}}$

$\tau \approx 90164.223\,kPa$

a) According to the maximum-shear-stress failure theory, we get that maximum shear stress limit is:

$S_{ys} = 0.5\cdot S_{ut}$ (Eq. 3)

Where:

$S_{ys}$ - Ultimate shear stress, measured in kilopascals.

$S_{ut}$ - Ultimate tensile stress, measured in kilopascals.

If we know that $S_{ut} = 440\times 10^{3}\,kPa$ , the ultimate shear stress of the material is:

$S_{ys} = 0.5\cdot (440\times 10^{3}\,kPa)$

$S_{ys} = 220\times 10^{3}\,kPa$

Lastly, the static factor of safety of the shaft (), dimensionless, is:

$n = \frac{S_{ys}}{\tau}$ (Eq. 4)

If we know that $S_{ys} = 220\times 10^{3}\,kPa$ and $\tau \approx 90164.223\,kPa$ , the static factor of safety of the shaft is:

$n = \frac{220\times 10^{3}\,kPa}{90164.223\,kPa}$

n = 2.440

According to the maximum-shear-stress failure theory, the static factor of safety of the shaft is 2.440.

b) According to the distortion-energy failure theory, we get that maximum shear stress limit is:

$S_{ys} = 0.577\cdot S_{ut}$ (Eq. 5)

If we know that $S_{ut} = 440\times 10^{3}\,kPa$ , the ultimate shear stress of the material is:

$S_{ys} = 0.577\cdot (440\times 10^{3}\,kPa)$

$S_{ys} = 253.88\times 10^{3}\,kPa$

Lastly, the static factor of safety of the shaft is:

$n = \frac{253.88\times 10^{3}\,kPa}{90164.223\,kPa}$

n = 2.816

According to the distortion-energy failure theory, the static factor of safety of the shaft is 2.816.

Answer from: Quest

In general, the greater the degree of undercooling of a liquid melt, the smaller the critical radius of the nuclei formed.

Answer from: Quest

the warning light flashes for a second or two when the engine starts. if it stays on, there's must be something wrong with the coolant. you should never dare to continue driving when the light is on. pull over as soon as possible and shut the engine off.

hope this is what you're talking about

Other questions on the subject: Engineering

Engineering, 04.07.2019 18:10, anna22684

Water at 70°f and streams enter the mixing chamber at the same mass flow rate, determine the temperature and the quality of the exiting stream. 0 psia is heated in a chamber by mixing it with saturated water vapor at 20 psia. if both streams enters the mixing chamber at the same mass flow rate, determine the temperature and the quality of the existing system.

Answers: 2

continue

Engineering, 04.07.2019 18:10, mirmir62

Machinery that is a key part of the process and without which the plant or process cannot function is classifed as: (clo4) a)-critical machinery b)-essential machinery c)-general purpose machinery d)-none of the specified options.

Answers: 1

continue

Engineering, 04.07.2019 18:20, myahlit84

Inadequate stores control is not an obstacle to effective work order system. (clo4) a)-true b)-false

Answers: 3

continue

Engineering, 04.07.2019 18:20, rbgrh9465

An open feedwater heater operates at steady state with liquid entering at inlet 1 with t? = 40°c and pl = 1 .2 mpa. water vapor att2-200°c and p2 = 1.2 mpa enters at inlet 2. saturated liquid water exits with a pressure of pa 1.2 mpa. neglect heat transfer with the surroundings and all kinetic and potential energy effects, determine the mass flow rate of steam at inlet 2 if the mass flow rate of liquid water at inlet 1 is given as 2 kg/s.

Answers: 3

continue

You know the right answer?

A 30-mm-diameter shaft, made of AISI 1018 HR steel, transmits 10 kW of power while rotating at 200 r...