Engineering, 22.08.2020 18:01 megan9246
An air conditioning system is used to provide cooling for a small office building in the summer. Cool dry air (State 2) is supplied to the conditioned space (State 3) to balance the total cooling load (QT for the space. Air exiting through return ducts is either recirculated or exhausted from the building. The recirculated air is mixed with a specified volume flow rate of outdoor air (State 0) to meet air quality requirements. The mixed air stream (State 1) is cooled to the dewpoint temperature (T1A and dehumidified by the cooling system to a relative humidity of 100% (State 1B). Finally, the air is reheated by a electric resistance coil heating system to the supply air conditions (State 2). Using the psychrometric chart, determine the following given the conditions below.
--Given Values--
T3 (F) = 76
T3wb (F) = 63
T0 (F) = 94
Phi0 () = 0.53
AV0 (cfm) = 501
QT (Btu/hr) = 59000
T1B (F) = 47
T3-T2 (F) = 15
a) Determine the humidity ratio at State 3.
Your Answer =
b) Determine the specific enthalpy (Btu/lb) at State 3.
Your Answer =
c) Determine the humidity ratio at State 2
Your Answer =
d) Determine the temperature (F) at State 2.
Your Answer =
e) Determine the specific enthalpy (Btu/lb) at State 2.
Your Answer =
f) Determine the specific enthalpy (Btu/lb) at State x.
Your Answer =
g) Determine the sensible heat factor for the space.
Your Answer =
h) Determine QS, the sensible heat transfer (Btu/h) for the space.
Your Answer =
i) Determine the mass flow rate (lb/h) at State 2.
Your Answer =
j) Determine the specific volume of the air (ft^3/lba) at State 2.
Your Answer =
k) Determine the volumetric flow rate (cfm) at State 2.
Your Answer =
l) Determine the specific volume of the air (ft^3/lba) at State 0.
Your Answer =
m) Determine the mass flow rate (lb/h) at State 0
Your Answer =
n) Determine the fraction (%) of outdoor air.
Your Answer =
o) Determine the humidity ratio at State 0.
Your Answer =
p) Determine the specific enthalpy (Btu/lb) at State 0.
Your Answer =
q) Determine the specific enthalpy (Btu/lb) at State 1.
Your Answer =
r) Determine the humidity ratio at State 1.
Your Answer =
s) Determine the temperature (F) at State 1.
Your Answer =
t) Determine the dew point temperature (F) for State 1.
Your Answer =
u) Determine the specific enthalpy (Btu/lb) at State 1B.
Your Answer =
v) Determine QC, the load (Btu/h) for the cooling system
Your Answer =
w) Determine QH, the load (Btu/h) for the reheat system.
Your Answer =
Answers: 1
Engineering, 04.07.2019 18:10, keigleyhannah30
Aplate clutch has a single pair of mating friction surfaces 250-mm od by 175-mm id. the mean value of the coefficient of friction is 0.30, and the actuating force is 4 kn. a) find the maximum pressure and the torque capacity using the uniform-wear model. b) find the maximum pressure and the torque capacity using the uniform-pressure model.
Answers: 3
Engineering, 04.07.2019 18:10, lerasteidl
Determine whether or not it is possible to compress air adiabatically from k to 140 kpa and 400 k. what is the entropy change during this process?
Answers: 3
Engineering, 04.07.2019 18:10, xboxdude06
Slip occurs via two partial dislocations because of (a) the shorter path of the partial dislocation lines; (b) the lower energy state through partial dislocations; (c) the charge balance.
Answers: 1
An air conditioning system is used to provide cooling for a small office building in the summer. Coo...
Mathematics, 26.09.2021 22:20
English, 26.09.2021 22:20
Mathematics, 26.09.2021 22:20
Mathematics, 26.09.2021 22:20
Mathematics, 26.09.2021 22:20
Mathematics, 26.09.2021 22:20
Mathematics, 26.09.2021 22:20