subject
Engineering, 29.07.2020 04:01 taylorbean315

Determine if each of the following statements is true or false. 1. Larger atoms are better nucleophiles due to polarizability.
A. True
B. False
2. The identity of the nucleophile affects the rate of an SN1 reaction.
A. True
B. False
3. SN2 reactions proceed via frontside attack.
A. True
B. False
4. Bimolecular reactions tend to be stereoselective.
A. True
B. False
5. SN2 reactions invert all stereocenters in a haloalkane.
A. True
B. False
6. Cl-, OH-, and H- are good all leaving groups.
A. True
B. False
7. Good bases tend to be good nucleophiles.
A. True
B. False
8. Branching adjacent to a reacting carbon slows SN2 reactions due to steric hindrance.
A. True
B. False
9. SN1 reactions are slowed by hyperconjugation of the carbocation intermediate.
A. True
B. False
10. The rate determining step for SN1 reactions is the same as the rate determining step for E1 reactions.
A. True
B. False
11. It is possible to get E1 alone but SN1 is always accompanied by E1.
A. True
B. False
12. Leaving group ability depends only on pKa of the conjugate acid.
A. True
B. False
13. Good nuclephiles are also good leaving groups.
A. True
B. False
14. Protic solvents solvate large ions better than small ions because of increased surface area.
A. True
B. False
15. Steric hindrance is a major factor in determining between SN2 and E2 mechanisms.
A. True
B. False
16. Backside attack always converts R to S and vice versa.
A. True
B. False
17. Nucleophile ability is solely dependent on the pka of the conjugate acid.
A. True
B. False
18. A high concentration of good nucleophile will increase the ratio of SN1 product to E1 product.
A. True
B. False

ansver
Answers: 1

Other questions on the subject: Engineering

image
Engineering, 03.07.2019 14:10, makaylashrout77
Amass of 1.5 kg of air at 120 kpa and 24°c is contained in a gas-tight, frictionless piston-cylinder device. the air is now compressed to a final pressure of 720 kpa. during the process, heat is transferred from the air such that the temperature inside the cylinder remains constant. calculate the boundary work input during this process.
Answers: 2
image
Engineering, 04.07.2019 18:10, bckyanne3
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
image
Engineering, 04.07.2019 18:20, myahlit84
Inadequate stores control is not an obstacle to effective work order system. (clo4) a)-true b)-false
Answers: 3
image
Engineering, 04.07.2019 18:20, sanchez626
Aheavily insulated piston-cylinder device contains 0.02 m3 of steam at 300 kpa and 200 °c. 1.2 mpa. d this process. team is now compressed in a reversible manner to a pressure of etermine the entropy change and the work done on the steam during this process
Answers: 1
You know the right answer?
Determine if each of the following statements is true or false. 1. Larger atoms are better nucleoph...

Questions in other subjects: