Engineering, 18.07.2020 01:01 hokamidat

The shaft is made of A992 steel. It has a diameter of 1 in. and is supported by bearings at A and D, which allows free rotation. For A992 steel, G = 11 × 103 ksi. (1) Determine the angle of twist of B with respect to D.(2) Determine the angle of twist of C with respect to D. Answer unit: degree or radians, two decimal places

Answers: 1

Show answers

Answers

Answer from: odetteerivera

the angle of twist of B with respect to D is -1.15°

the angle of twist of C with respect to D is 1.15°

Explanation:

The missing diagram that is supposed to be added to this image is attached in the file below.

From the given information:

The shaft is made of A992 steel. It has a diameter of 1 in and is supported by bearing at A and D.

For the Modulus of Rigidity G = 11 × 10³ Ksi = 11 × 10⁶ lb/in²

The objective are :

1) To determine the angle of twist of B with respect to D

Considering the Polar moment of Inertia at the shaft $J\tau$

shaft $J\tau$ = $\dfrac{\pi}{2}r^4$

where ;

r = 1 in /2

r = 0.5 in

shaft $J \tau$ = $\dfrac{\pi}{2} \times 0.5^4$

shaft $J\tau$ = 0.098218

Now; the angle of twist at B with respect to D is calculated by using the expression

$\phi_{B/D} = \sum \dfrac{TL}{JG}$

$\phi_{B/D} = \dfrac{T_{CD}L_{CD}}{JG}+\dfrac{T_{BC}L_{BC}}{JG}$

where;

$T_{CD} \ \ and \ \ L_{CD}$ are the torques at segments CD and length at segments CD

${T_{BC} \ \ and \ \ L_{BC}}$ are the torques at segments BC and length at segments BC

Also ; from the diagram; the following values where obtained:

$L_{BC}}$ = 2.5 in

$J\tau$ = 0.098218

G = 11 × 10⁶ lb/in²

$T_{BC$ = -60 lb.ft

$T_{CD$ = 0 lb.ft

$L_{CD$ = 5.5 in

$\phi_{B/D} = 0+ \dfrac{[(-60 \times 12 )] (2.5 \times 12 )}{ (0.9818)(11 \times 10^6)}$

$\phi_{B/D} = \dfrac{[(-720 )] (30 )}{1079980}$

$\phi_{B/D} = \dfrac{-21600}{1079980}$

$\phi_{B/D} =$ − 0.02 rad

To degree; we have

$\phi_{B/D} = -0.02 \times \dfrac{180}{\pi}$

$\mathbf{\phi_{B/D} = -1.15^0}$

Since we have a negative sign; that typically illustrates that the angle of twist is in an anti- clockwise direction

Thus; the angle of twist of B with respect to D is 1.15°

(2) Determine the angle of twist of C with respect to D.Answer unit: degree or radians, two decimal places

For the angle of twist of C with respect to D; we have:

$\phi_{C/D} = \dfrac{T_{CD}L_{CD}}{JG}+\dfrac{T_{BC}L_{BC}}{JG}$

$\phi_{C/D} = 0+\dfrac{T_{BC}L_{BC}}{JG}$

$\phi_{B/D} = 0+ \dfrac{[(60 \times 12 )] (2.5 \times 12 )}{ (0.9818)(11 \times 10^6)}$

$\phi_{C/D} = \dfrac{21600}{1079980}$

$\phi_{C/D} =$ 0.02 rad

To degree; we have

$\phi_{C/D} = 0.02 \times \dfrac{180}{\pi}$

$\mathbf{\phi_{C/D} = 1.15^0}$

The shaft is made of A992 steel. It has a diameter of 1 in. and is supported by bearings at A and D,

Answer from: Quest

Because if a good speech is delivered badly it can bore the audience, confuse them, or make them distrust the speakeri think they all come back to this one, except that last answer because that is false. if your audience starts making fun of you or gets distracted it is because they are either bored, confused or distrust you.

Answer from: Quest

answer:

explanation:

assault rifle is a rapid-fire, magazine-fed rifle designed for military use. it is a shoulder-fired weapon that allows the shooter to select between semi-automatic (requiring you pull the trigger for each shot), fully automatic (hold the trigger and the gun continuously fires) or three-shot-burst modes.

Other questions on the subject: Engineering

Engineering, 04.07.2019 18:10, heidiburgos1own6c0

Fluids at rest possess no flow energy. a)- true b)- false

Answers: 3

continue

Engineering, 04.07.2019 18:10, abdirahmansoloman

Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.4-m-long tubes inside which the refrigerant is evaporating at -20°c. air approaches the tube bank in the normal direction at 0°c and 1 atm with a mean velocity of 4 m/s. the tubes are arranged in-line with longitudinal and transverse pitches of sl- st 1.5 cm. there are 30 rows in the flow direction with 15 tubes in each row. determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. evaluate the air properties at an assumed mean temperature of -5°c and 1 atm. is this a good assumption?

Answers: 1

continue

Engineering, 04.07.2019 18:10, selenamr

Ifa component is made of two or more materials with different modulus of elasticity (e), it is called a composite member and we calculate the factor·n". mention the formula for calculating n". also, ifn> 1, explain what will happen to the 1. transformed. gi) ifn 1, what will happen to the material when transformed material when

Answers: 1

continue

Engineering, 04.07.2019 18:10, oliviasoreo92

Compute the pressure drop of 30°c air flowing with a mean velocity of 8 m/s in a circular sheet-metal duct 300 mm in diameter and 15 m long. use a friction factor, f 0.02, and pair = 1.1644 kg/m a. 37.26 pa b. 25.27 pa n c. 29.34 pa d. 30.52 pa

Answers: 1

continue

You know the right answer?

The shaft is made of A992 steel. It has a diameter of 1 in. and is supported by bearings at A and D,...