subject
Engineering, 19.06.2020 03:57 alyssabailey7545

You are required to design a heating oven for sterilizing equipment. The oven is heated by side heater imbedded at the mid-plan of a wall of 20 cm thick. The wall is completely insulated from the air side. The material of the oven walls has k = 10 W/m K and the thickness of each wall other than that mentioned is 10 cm. The top and the bottom sides of the oven are completely insulated. The amount of heat lost from the walls should not exceed 5% of the input power to the heater which is 2kW. In order to enhance the heat transfer from the wall where the heater is fitted to the oven space, it is proposed to attach a number of either longitudinal or transverse fins to this wall. The dimensions of each one of these fins as follows; its length is 15 cm and thickness is 3mm. The fin material is aluminum with k = 150 W/m K. The oven is cubical in shape with side length 75 cm. If the inside temperature of air inside the oven should be 75°C and the ambient temperature of the air outside the oven varies from 25°C to 40 °C. All the heat generated by the heater is transferred normal to its wall. Assume an average fin temperature to calculate the heat transfer coefficient from fins to the oven space. After then use this value of h to calculate the heat transfer from single fin and then find the number of fins required to transfer the heat, assuming adiabatic tip fin, bearing in mind that heat is also transferred from bare area of the wall where the fins are attached. Explain which type of fins you recommend (longitudinal or transverse fins). (Comment of your results) Until here [50% of Total] It is required also to select suitable insulating material used for this application and to calculate the thickness of this material to suit the given condition of heat loss. Until here [65% of Total] Assume the gas in the oven to be a lumped capacitance system, calculate in this case the time required for the air in the oven to reach the set temperature If the heated wall does not attached with fins, estimate the power of the heater and the time required for the air in the oven to reach the set temperature (Comment of your results) Until here [ 100% of total] You are required to provide all missing properties stating the source from which this data are obtained.

ansver
Answers: 2

Other questions on the subject: Engineering

image
Engineering, 03.07.2019 14:10, makaylashrout77
Amass of 1.5 kg of air at 120 kpa and 24°c is contained in a gas-tight, frictionless piston-cylinder device. the air is now compressed to a final pressure of 720 kpa. during the process, heat is transferred from the air such that the temperature inside the cylinder remains constant. calculate the boundary work input during this process.
Answers: 2
image
Engineering, 04.07.2019 18:10, niyawilliams23
Asingle-geared blanking press has a stroke of 200 mm and a rated capacity of 320 kn. a cam driven ram is assumed to be capable of delivering the full press load at constant force during the last 15 percent of a constant-velocity stroke. the camshaft has an average speed of 90 rev/min and is geared to the flywheel shaft at a 6: 1 ratio. the total work done is to include an allowance of 16 percent for friction a) estimate the maximum energy fluctuation b) find the rim weight for an effective diameter of 1.2 m and a coefficient of speed fluctuation of 0.10
Answers: 1
image
Engineering, 04.07.2019 18:10, michellerosas
Ajournal bearing has a journal diameter of 3.250 in with a unilateral tolerance of 20.003 in. the bushing bore has a diameter of 3.256 in and a unilateral tolerance of 0.004 in. the bushing is 2.8 in long and supports a 700-lbf load. the journal speed is 900 rev/min. find the minimum oil film thickness and the maximum film pressure for both sae 20 and sae 20w-30 lubricants, for the tightest assembly if the operating film temperature is 160°f. a computer code is appropriate for solving this problem.
Answers: 3
image
Engineering, 04.07.2019 18:10, siri5645
At 12 noon, the count in a bacteria culture was 400; at 4: 00 pm the count was 1200 let p(t) denote the bacteria cou population growth law. find: (a) an expression for the bacteria count at any time t (b) the bacteria count at 10 am. (c) the time required for the bacteria count to reach 1800.
Answers: 1
You know the right answer?
You are required to design a heating oven for sterilizing equipment. The oven is heated by side heat...

Questions in other subjects:

Konu
Mathematics, 12.10.2020 22:01
Konu
Mathematics, 12.10.2020 22:01
Konu
History, 12.10.2020 22:01