![subject](/tpl/images/cats/User.png)
Engineering, 06.06.2020 13:58 jennifercastillo1233
In the system shown in the figure, atmospheric air is sucked from the section 1 with a compressor with a pressure of 5,ab bar. 25% of the sucked air from tank A is delivered to turbine after passing a nozzle., inlet and outlet diameters of a nozzle having 10ab mm long are 2abmm and 1abmm respectively; And then the air leaving the turbine is discharged into the atmosphere with a very short pipe with a diameter of 1abmm and 10ab m long. Take the absolute pressure in tank A is 5,ab bar, find the power of the turbine and the electrical energy generated by the generator for 3a, b % of the total efficiency. the pipes used in the system are made of galvanized pipes (roughness value ε = 0.15mm). Solve the problem by making the necessary assumptions and drawing the schematic figure. Minor loss coefficients are K1=0,5ab, K2=K4=1.ab, and K3 will be calculated
![ansver](/tpl/images/cats/User.png)
Answers: 3
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Other questions on the subject: Engineering
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, alyssabailey7545
Give heat transfer applications for the following, (i) gas turbines (propulsion) ) gas turbines (power generation). (iii) steam turbines. (iv) combined heat and power (chp). (v) automotive engines
Answers: 1
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10, batmanmarie2004
Afoot bridge is made as a simple deck, 4 m long, with a cross section 2 m (wide) and 20 cm thick, and made of wood. the deck is supported at the two ends. the maximum load allowable on the bridge is 10 tons, provided it is uniformly distributed on the deck. to sense this load, a strain gauge is placed at the center of the bridge and its resistance is monitored. if the sensor has a nominal resistance of 350 s2 and a gauge factor of 3.6, what is the reading of the strain gauge at maximum load? the modulus of elasticity for the wood used in the construction is 10 gpa.
Answers: 2
![image](/tpl/images/cats/User.png)
![image](/tpl/images/cats/User.png)
Engineering, 06.07.2019 02:30, josediaz1124
Around steel bar, made from material with a yield stress of 750mpa, is loaded so that it has stresses co locations of maximum normal stress and maximum shear stress. use maximum shear stress and maximum distortion energy theories to calculate the safety factors for initial yielding failures.
Answers: 3
You know the right answer?
In the system shown in the figure, atmospheric air is sucked from the section 1 with a compressor wi...
Questions in other subjects:
![Konu](/tpl/images/cats/mkx.png)
![Konu](/tpl/images/cats/fizika.png)
![Konu](/tpl/images/cats/fizika.png)
Physics, 29.10.2020 02:20
![Konu](/tpl/images/cats/mat.png)
Mathematics, 29.10.2020 02:20
![Konu](/tpl/images/cats/mat.png)
Mathematics, 29.10.2020 02:20
![Konu](/tpl/images/cats/informatica.png)
Computers and Technology, 29.10.2020 02:20
![Konu](/tpl/images/cats/biologiya.png)
![Konu](/tpl/images/cats/biologiya.png)
Biology, 29.10.2020 02:20
![Konu](/tpl/images/cats/biologiya.png)
![Konu](/tpl/images/cats/es.png)
Spanish, 29.10.2020 02:20