Engineering, 21.05.2020 16:59 desiree98

Design a sequential circuit for a stoplight controller. The stoplight will have four states: the standard green, yellow, and red, and also a flashing red state. The flashing red occurs when there is a power outage and the backup generator outputs an active signal (HIGH). Under normal operation (when the backup generator is not active), a separate timer signal outputs HIGH when it is time to change to the next light in the sequence. If leaving the flashing red state (when generator signal drops LOW), then the light should return to green. Note that there is not a signal for emergency vehicles.(a) Draw the State Diagram. Make it clear what each state name means. Follow a straight binary count with the state codes. (b) Draw the Transition Table. Use J-K Flip-Flops for this design.(c) Make the Next-State Table.(d) Derive the Boolean equations. Remember one equation for each flip-flop input and for each output.

Answers: 3

Show answers

Other questions on the subject: Engineering

Engineering, 04.07.2019 18:10, abdirahmansoloman

Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.4-m-long tubes inside which the refrigerant is evaporating at -20°c. air approaches the tube bank in the normal direction at 0°c and 1 atm with a mean velocity of 4 m/s. the tubes are arranged in-line with longitudinal and transverse pitches of sl- st 1.5 cm. there are 30 rows in the flow direction with 15 tubes in each row. determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. evaluate the air properties at an assumed mean temperature of -5°c and 1 atm. is this a good assumption?

Answers: 1

continue

Engineering, 04.07.2019 18:20, CelesteN64

Most leaks in reciprocating air compressors can be detected and minimized by: (clo4) a)-detecting leakage areas using ultrasonic acoustic detector. b)-tightening joints and connections c)-replacing faulty equipment d)-all of the given options

Answers: 2

continue

Engineering, 04.07.2019 19:10, ndaha

An external consultant recommends that a plant installs a bank of capacitors for power factor correction. this will reduce the peak electrical demand charges by an average of 93 kw every month. the plant current pays $13 per kw in peak demand charges. the capacitor bank will include 223 kw of fixed capacitors, and 183 of variable capacitors. the fixed capacitors cost $59 per kw, and the variable capacitors will cost $65 per kw. the consultant charges 21% of the equipment costs to install the capacitors. because this project will reduce the demand for the electric utility, they are prepared to provide a one-time rebate of $42 per kw of reduced demand. what is the simple payback period for this project (in years)?

Answers: 2

continue

Engineering, 04.07.2019 19:20, mariahmimibrooks

Liquid flows at steady state at a rate of 2 lb/'s through a pump, which operates to raise the elevation of the liquid 100 ft from control volume inlet to exit. the liquid specific enthalpy at the inlet is 40.09 btu/lb and at the exit is 40.94 btub. the pump requires 3 btu/s of power to operate. if kinetic energy effects are negligible and gravitational acceleration is 32.174 tt/s, the heat transfer rate associated with this steady state process is most closely 1)-2,02 btu/s from the liquid to the surroundings 2)-3.98 btu/s from the surroundings to the liquid. 3)-4.96 btu/s from the surroundings to the liquid. 4)-1.04 btu/s from the liquid to the surroundings.

Answers: 2

continue

You know the right answer?

Design a sequential circuit for a stoplight controller. The stoplight will have four states: the sta...