![subject](/tpl/images/cats/User.png)
Engineering, 15.04.2020 15:49 alyssaflores
Write a method printShampooInstructions(), with int parameter numCycles, and void return type. If numCycles is less than 1, print "Too few.". If more than 4, print "Too many.". Else, print "N: Lather and rinse." numCycles times, where N is the cycle number, followed by "Done.". End with a newline. Example output with input 2: 1: Lather and rinse. 2: Lather and rinse. Done.
![ansver](/tpl/images/cats/User.png)
Answers: 3
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Other questions on the subject: Engineering
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10, Destinationz
Asteam is contained in a rigid tank with a volume of 1 m3. initially, the pressure and temperature are 7 bar and 500 oc, respectively. the temperature drops due to cooling process. determine: (1) the temperature at which condensation begins in °c, (2) the fraction of the total mass that has condensed when the pressure decreased to 0.5 bar. (3) the volume in m3 occupied by saturated liquid at the final state?
Answers: 3
![image](/tpl/images/cats/User.png)
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20, rida10309
At steady state, air at 200 kpa, 325 k, and mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross-sectional areas. the inlet cross-sectional area is 6 cm2. at the duct exit, the pressure of the air is 100 kpa and the velocity is 250 m/s. neglecting potential energy effects and modeling air as an 1.008 kj/kg k, determine ideal gas with constant cp = (a) the velocity of the air at the inlet, in m/s. (b) the temperature of the air at the exit, in k. (c) the exit cross-sectional area, in cm2
Answers: 2
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20, mercedesamatap21hx0
To design a steam turbine to produce 12,000 hp power. a engineer comsiders using a steady state stean low st 1160fr and engineer considers using a steady state steam flow at 1160°r and 450 psia to drive this steam turbine. the exhaust of the steam is cooled by the lake (vacuum). heat losing to the surroundings is measured at a rate of 555.55 btu/s. (a) sketch the system with the given conditions. (b) neglecting kinetic and potential energy changes from inlet to exit, determine the volumetric flow rate of the steam at the inlet, (ft'/hr). must clearly show unit conversions at crtical terms.
Answers: 1
You know the right answer?
Write a method printShampooInstructions(), with int parameter numCycles, and void return type. If nu...
Questions in other subjects:
![Konu](/tpl/images/cats/biologiya.png)
![Konu](/tpl/images/cats/mat.png)
Mathematics, 10.03.2022 08:10
![Konu](/tpl/images/cats/mat.png)
Mathematics, 10.03.2022 08:10
![Konu](/tpl/images/cats/mat.png)
Mathematics, 10.03.2022 08:10
![Konu](/tpl/images/cats/mat.png)
![Konu](/tpl/images/cats/mat.png)
![Konu](/tpl/images/cats/biologiya.png)
![Konu](/tpl/images/cats/en.png)
English, 10.03.2022 08:10
![Konu](/tpl/images/cats/mat.png)