![subject](/tpl/images/cats/User.png)
Engineering, 15.04.2020 00:09 Becky81
A bar of steel has the minimum properties Se = 40 kpsi, Sy = 60 kpsi, and Sut = 80 kpsi. The bar is subjected to a steady torsional stress of 15 kpsi, an alternating torsional stress of 10 kpsi, and an alternating bending stress of 12 kpsi. Find the factor of safety guarding against a static failure, and the factor of safety guarding against a fatigue failure, and find the expected life of the part. For the fatigue analysis use:
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Other questions on the subject: Engineering
![image](/tpl/images/cats/User.png)
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, demarcuswiseman
Calculate the bore of a cylinder that has a stroke of 18 inches and an extension time of 6 seconds at a flow rate of 4 gal/min.
Answers: 3
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20, Katmcfee7681
Acommercial grade cubical freezer, 4 m on a side, has a composite wall consisting of an exterior sheet of 5.0-mm thick plain carbon steel (kst= 60.5 w/m k), an intermediate layer of 100-mm thick polyurethane insulation (kins 0.02 w/m k), and an inner sheet of 5.0- mm thick aluminium alloy (kal polyurethane insulation and both metallic sheets are each characterized by a thermal contact resistance of r 2.5 x 104 m2 k/w. (a) what is the steady-state cooling load that must be maintained by the refrigerator under conditions for which the outer and inner surface temperatures are 25°c and -5°c, respectively? (b) for power saving purpose, which wall material should be increased/reduced in. thickness in order to reduce 50% of the cooling load found in part (a)? redesign the thickness of the proposed material. 177 w/m-k). adhesive interfaces between the q=575.93 w
Answers: 2
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20, nikkiebartels
Afan that can provide air speeds up to 60 m/s is to be used in a low-speed wind tunnel with atmospheric air at 35 c. if one wishes to use the wind tunnel to study flat-plate boundary layer behavior up to reynolds numbes of re 10, what is the minimum plate length that should be used? at what distance from the leading edge would transition occur if the critical reynolds nurnber were rer, e = 5 × 105?
Answers: 2
You know the right answer?
A bar of steel has the minimum properties Se = 40 kpsi, Sy = 60 kpsi, and Sut = 80 kpsi. The bar is...
Questions in other subjects:
![Konu](/tpl/images/cats/geografiya.png)
Geography, 11.01.2020 16:31
![Konu](/tpl/images/cats/mkx.png)
Arts, 11.01.2020 16:31
![Konu](/tpl/images/cats/en.png)
![Konu](/tpl/images/cats/biologiya.png)
Biology, 11.01.2020 16:31
![Konu](/tpl/images/cats/mat.png)
Mathematics, 11.01.2020 16:31
![Konu](/tpl/images/cats/biologiya.png)
![Konu](/tpl/images/cats/en.png)
English, 11.01.2020 16:31
![Konu](/tpl/images/cats/istoriya.png)
![Konu](/tpl/images/cats/ap.png)
Advanced Placement (AP), 11.01.2020 16:31
![Konu](/tpl/images/cats/mat.png)
Mathematics, 11.01.2020 16:31