Engineering, 31.03.2020 00:26 quianna410

A sleeve made of SAE 4150 annealed steel has a nominal inside diameter of 3.0 inches and an outside diameter of 4.0 inches. It is pressed onto a solid shaft with a medium drive force fit. Specify the class of fit, dimensions for the shaft and sleeve, and calculate the stress in the shaft and sleeve after installation. Use the basic hole system. Is the design acceptable

Answers: 1

Show answers

Answers

Answer from: drandbone92

Class of fit:

Interference (Medium Drive Force Fits constitute a special type of Interference Fits and these are the tightest fits where accuracy is important).

Here minimum shaft diameter will be greater than the maximum hole diameter.

Medium Drive Force Fits are FN 2 Fits.

As per standard ANSI B4.1 :

Desired Tolerance: FN 2

Tolerance TZone: H7S6

Max Shaft Diameter: 3.0029

Min Shaft Diameter: 3.0022

Max Hole Diameter:3.0012

Min Hole Diameter: 3.0000

Max Interference: 0.0029

Min Interference: 0.0010

Stress in the shaft and sleeve can be considered as the compressive stress which can be determined using load/interference area.

Design is acceptable If compressive stress induced due to selected dimensions and load is less than compressive strength of the material.

Explanation:

Answer from: amanquen35

Design is acceptable.

Explanation:

Class of fit: Interference (Medium Drive Force Fits constitute a special kind of Interference Fits and these are the tightest fits where accuracy is important).

So, minimum shaft diameter will be larger than the maximum hole diameter.

Medium Drive Force Fits are FN 2 Fits.

As per standard ANSI B4.1 :

Desired Tolerance: FN 2

Tolerance TZone: H7S6

Max Shaft Diameter: 3.0029

Min Shaft Diameter: 3.0022

Max Hole Diameter:3.0012

Min Hole Diameter: 3.0000

Max Interference: 0.0029

Min Interference: 0.0010

Stress in the shaft and sleeve can be taking note of as the compressive stress which can be determined using load/interference area.

Design is acceptable If compressive stress induced due to selected dimensions and load is less than compressive strength of the material.

Answer from: Quest

answer:

i lost in getting someone back.

i learned that people are really two-faced and no matter how angelic someone appears they always have a devil side and that you cant trust anyone anymore no matter how dear they are to you.

if your wondering who it waz it waz mah still miss her tho

~batmans wife dun dun

Answer from: Quest

answer:

put more,

Other questions on the subject: Engineering

Engineering, 03.07.2019 23:20, abbz13

Two technicians are discussing the intake air temperature (iat) sensor. technician a says that the computer uses the iat sensor as a backup to the engine coolant temperature (ect) sensor. technician b says that the powertrain control module (pcm) will subtract the calculated amount of fuel if the air measures hot. who is correct

Answers: 3

continue

Engineering, 04.07.2019 18:10, ahmedeldyame

Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.

Answers: 1

continue

Engineering, 04.07.2019 18:10, meganwintergirl

Afour cylinder four-stroke in-line engine has a stroke of 160mm, connecting rod length of 150mm, a reciprocating mass of 3kg and its firing order is 1-3-4-2. the spacing between cylinders is 100mm. i. show that the engine is in balance with regard to the primary inertia forces and primary 3. a and secondary inertia couples. li determine the out of balance secondary inertia force ii. propose ways of balancing this out of balance force and discuss the challenges that will arise

Answers: 3

continue

Engineering, 04.07.2019 18:10, keigleyhannah30

Aplate clutch has a single pair of mating friction surfaces 250-mm od by 175-mm id. the mean value of the coefficient of friction is 0.30, and the actuating force is 4 kn. a) find the maximum pressure and the torque capacity using the uniform-wear model. b) find the maximum pressure and the torque capacity using the uniform-pressure model.

Answers: 3

continue

You know the right answer?

A sleeve made of SAE 4150 annealed steel has a nominal inside diameter of 3.0 inches and an outside...