Engineering, 27.03.2020 01:53 tylerjoshonti

Suppose you work in a lab to develop a robotic fish that can swim at various depths of the ocean. A part of the robotic fish can be considered as a metal block that is exposed to the compressive pressure p that the water exerts on all sides of the block. Besides the compressive pressure p, the only other stress that the metal block is subject to is a shear stress loading Txy. Hence, the other two shear stresses are zero ( Txz = Tyz = 0). The yield strength of this metal is 0. = 300 MPa.

(a) Suppose the robotic fish swims in a depth of the ocean where the water pressure loading is p= 90 MPa. Use the Octahedral Shear Stress Yield Criterion (i. e. the von Mises Yield Criterion) to determine the largest value of Txy that can be apply if we want a safety factor against yielding of X.= 1.5?
(b) Suppose the robotic fish then swims in a depth where the water pressure loading is 20 times more, i. e. p = 1,800 MPa. Use the Octahedral Shear Stress Yield Criterion (i. e. the von Mises Yield Criterion) to determine the largest value of Txy that can be apply if we want a safety factor against yielding of Xo = 1.5 ?

Answers: 2

Show answers

Other questions on the subject: Engineering

Engineering, 04.07.2019 18:20, RiverH246

Air flows over a heated plate àt a velocity of 50m/s. the local skin factor coefficient at a point on a plate is 0.004. estimate the local heat transfer coefficient at this point. the following property data for air are given: density = 0.88kg/m3 , viscosity 2.286 x 10 ^-5 kgm/s , k = 0.035w/mk ,cp = 1.001kj/kgk. use colburn reynolds analogy.

Answers: 1

continue

Engineering, 04.07.2019 19:10, batmanmarie2004

Afoot bridge is made as a simple deck, 4 m long, with a cross section 2 m (wide) and 20 cm thick, and made of wood. the deck is supported at the two ends. the maximum load allowable on the bridge is 10 tons, provided it is uniformly distributed on the deck. to sense this load, a strain gauge is placed at the center of the bridge and its resistance is monitored. if the sensor has a nominal resistance of 350 s2 and a gauge factor of 3.6, what is the reading of the strain gauge at maximum load? the modulus of elasticity for the wood used in the construction is 10 gpa.

Answers: 2

continue

Engineering, 04.07.2019 19:10, thawkins79

Agas contained within a piston-cylinder assembly e end nation about same energy states, 1 and 2, where pi 10 bar, v undergoes two processes, a and b, between the sam 0.1 m3, ui-400 kj and p2 1 bar, v2 1.0 m2, u2 200 kj: process a: process from 1 to 2 during which the pressure- volume relation is pv constant process b: constant-volume process from state 1 to a pressure of 2 bar, followed by a linear pressure-volume process to +20 0 state 2 kinetic and potential energy effects can be ignored. for each of the processes a and b, (a) sketch the process on p-v coordinates, (b) evaluate the work, in kj, and (c) evaluate process the heat transfer, in kj

Answers: 2

continue

Engineering, 04.07.2019 19:20, mariahmimibrooks

Liquid flows at steady state at a rate of 2 lb/'s through a pump, which operates to raise the elevation of the liquid 100 ft from control volume inlet to exit. the liquid specific enthalpy at the inlet is 40.09 btu/lb and at the exit is 40.94 btub. the pump requires 3 btu/s of power to operate. if kinetic energy effects are negligible and gravitational acceleration is 32.174 tt/s, the heat transfer rate associated with this steady state process is most closely 1)-2,02 btu/s from the liquid to the surroundings 2)-3.98 btu/s from the surroundings to the liquid. 3)-4.96 btu/s from the surroundings to the liquid. 4)-1.04 btu/s from the liquid to the surroundings.

Answers: 2

continue

You know the right answer?

Suppose you work in a lab to develop a robotic fish that can swim at various depths of the ocean. A...