Engineering, 17.03.2020 03:23 masogreene123

You are testing a new jet engine in a test cell at sea level conditions. You measure the mass flow through the engine and find it is 125 kg/sec of air plus 2.5 kg/sec of fuel. The velocity ahead of the engine may be assumed to be zero (it is a static test). The velocity of the exhaust is 340 meters/second. The load cell in the test stand (which measures engine thrust) reads 60,000 Newtons. Is the load cell reading correctly within 2%? If not, what should the load cell read?

Answers: 2

Show answers

Answers

Answer from: gabegabemm1

43248 newtons.

Explanation:

Force = mass x accelerations and units of force are newtons which are given in the question.

here mass = 125 of air and 2.2 of fuel, total = 125+2.2=127.5kg/s and the velocity of the exhaust is 340m/s.

force = 340m/s * 127.5kg/s = 43248 newtons technically this is wrong (observe units) but i will expalin how i have taken acceleration as a velocity here and mass/unit time as simply mass.

see force is mass times acceleration or deceleration, here our velocity is not changing therefore it is constant 340m/s but if it were to change and become 0 in one second then there would be -340m/s^2 (note the units ) of deceleration and there would be force associated with it and that force is what i have calculated here. similarly there would be mass in flow rate of mass per second, which is also in that one second of time.

let's calculate error.

error = (actual-calculated)/actual. = (43248-60000)/43248= -38.734% less is ofcourse greater than 2%.

So the load cell is not reading correct to within 2% and it should read 43248newtons.

Answer from: erin93

The answer is 43350 newton

Explanation:

As per the question,

Mass=125.

Air =2.5

Velocity=340.

So the formula is,

F=ma.

Total=125+2.5=127.5

Applies the formula now,

F=ma

force = 340×127.5 = 43350

Calculate error now,

Error=((actual-calculated)/actual))

(43350-60000)/43350= -38.40%

Hence greater than 2%.

Answer from: Quest

answer:

yes

explanation:

Answer from: Quest

angvrswer:

vfg

grfhrtrhr:

jjj

yjujuju

jujuhuyhyt

bgf

bgr

gbr

bgr

gtr

bgr

gbgbbg

bgg

bbg

bfg

dcwf

fdb

ggb

rfe

gtg

gegte

gff

dfg

gfdsax

cvfbgnh

jmhngf

dsaazxscvb

nmhgb

fvdcsxaz

zxcv

bghn

Other questions on the subject: Engineering

Engineering, 04.07.2019 12:10, Ryantimes2

On a average work day more than work place firs are reorted

Answers: 1

continue

Engineering, 04.07.2019 18:10, chadatkin

Which of the following ziegler nichols tuning methods the response of the controller to a step input should exhibit an s-shaped curve? a)-open loop mode b)-closed loop mode c)-both modes (open & closed) d)-none of the modes (open & closed)

Answers: 3

continue

Engineering, 04.07.2019 18:10, tobyhollingsworth178

Which from the following instrument is commonly used to detect the high pitch butzing sound in bearings? [clo4] a)-digital ultrasonic meter b)-infrared camera c)-spectroscopic d)-vibrometer

Answers: 2

continue

Engineering, 04.07.2019 19:10, jimena15

10 kg of co2 is initially contained at 400 kpa and 300 k. the gas constant for carbon dioxide is 189 j/lkg k) and has a specific heat ratio, k, of 1.289. isentropic expansion then occurs until the pressure is 200 kpa. a) determine the initial volume of co2 in m. b) determine the final temperature in k. c) determine the work done by the system during the expansion kl.

Answers: 2

continue

You know the right answer?

You are testing a new jet engine in a test cell at sea level conditions. You measure the mass flow t...