subject
Engineering, 14.03.2020 06:14 orlando19882000

The roof of a refrigerated truck compartment is of composite construction, consisting of a layer of foamed urethane insulation (t2 = 50 mm, ki= 0.026 W/m-k) sandwiched between aluminum alloy panels (t1=5mm and Kp=180 W/m · K). The length and width of the roof are L = 10m and W = 3.5 m , respectively, and the temperature of the inner Ts, i = -100 C Consider conditions for which the truck is moving at a speed of V = 105 km/h, the air temperature is T? = 32°C, and the solar irradiation is Gs = 750 W/m2 • Turbulent flow be assumed over the entire length of the roof. (a) For equivalent values of the solar absorptivity and the emissivity of the outer surface (?s = ? = 0.5), estimate the average temperature Ts. o of the outer surface. What is the corresponding heat load imposed on the refrigeration system?(b) A special finish (?s = 0.15, ?= 0.8) may be applied to the outer surface. What effect would such an application have on the surface temperature and the heat load?(c) If, with ?s = ? = 0.5, the roof is not insulated (t2 = 0), what are the corresponding values of the surface temperature and the heat load?Thermal Paint

ansver
Answers: 1

Other questions on the subject: Engineering

image
Engineering, 04.07.2019 18:10, meganwintergirl
Afour cylinder four-stroke in-line engine has a stroke of 160mm, connecting rod length of 150mm, a reciprocating mass of 3kg and its firing order is 1-3-4-2. the spacing between cylinders is 100mm. i. show that the engine is in balance with regard to the primary inertia forces and primary 3. a and secondary inertia couples. li determine the out of balance secondary inertia force ii. propose ways of balancing this out of balance force and discuss the challenges that will arise
Answers: 3
image
Engineering, 04.07.2019 18:10, 0436500
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
image
Engineering, 04.07.2019 19:10, shunna33
Plan an experiment to measure the surface tension of a liquid similar to water. if necessary, review the ncfmf video surface tension for ideas. which method would be most suitable for use in an undergraduate laboratory? what experimental precision could be expected?
Answers: 2
image
Engineering, 04.07.2019 19:20, littlepotato10
To save energy, the air supply to a 2000 ft office has been shut off overnight and the room temperature has dropped to 40°f. in the morning, the thermostat is reset to 70°f and warm air at 120 f begins to flov in at 200ft'/min. the air is well mixed within the room, and an equal mass flow of air at room temperature (changing with time) is withdrawn through a return duct. the air pressure is nearly 1 atm everywhere. ignoring heat transfer with the surroundings and kinetic and potential energy effects, estimate how long it takes for the room temperature to reach 70°f. plot the room temperature as a function of time.
Answers: 1
You know the right answer?
The roof of a refrigerated truck compartment is of composite construction, consisting of a layer of...

Questions in other subjects:

Konu
Mathematics, 26.03.2021 01:00
Konu
Mathematics, 26.03.2021 01:00
Konu
Social Studies, 26.03.2021 01:00