Engineering, 10.03.2020 08:22 QuestionsAnsweredNow

Kirchoff's Law states that, by the time current has returned to its source, all
must be used
Resistance
Electron flow
Voltage
Wattage

Answers: 3

Show answers

Answers

Answer from: Kassi07

Kirchoff's Law Kirchoff's Law states that, by the time current has returned to its source is explained in the following.

Explanation:

Kirchhoff's Current Law (KCL) is Kirchhoff's first law that deals with the conservation of charge entering and leaving a junction. ... In other words the algebraic sum of ALL the currents entering and leaving a junction must be equal to zero.Kirchoff's laws apply for a given instant in time. So the voltages at a given moment around a loop will all sum to zero, or currents in a node sum to zero if you look at the instantaneous voltage and current. But they will be out of phase.Kirchhoff Voltage Law states that ''The algebraic sum of all voltages (source voltage and voltage drops) is equal to zero around a close path''. This is called KVL ( Kirchhoff Voltage Law) equation. The source voltage is equal to the sum of all voltage drops. Kirchhoff's Voltage Law (KVL) is Kirchhoff's second law that deals with the conservation of energy around a closed circuit path. Kirchhoff's laws can be used to determine the values of unknown values like current, Voltage in the circuit. These laws can be applied on any circuit (with some limitation), and useful to find the unknown values in complex circuits and networks.

Answer from: lizredrose5

Kirchoff's law states that by the time current has reached to its source all voltage must be used.

Explanation:

Kirchoff's voltage law states that the algebraic sum of all the voltages across a closed loop is zero. As the circuit is a closed conducting path, no energy is lost. ices All the voltage that is supplied from the voltage source is dropped at the devices in the circuit.

The potential difference maintained by the voltage source enables the flow of current across the circuit. As the supplied voltage drops at each elements of the circuit, all voltage is used by the time current has returned to the surface.

Answer from: Quest

answer:

i dont know but you should start brainstorming ideas like how would you post them

explanation:

Answer from: Quest

answer:

fvbyunjk

explanation:

Other questions on the subject: Engineering

Engineering, 04.07.2019 18:10, bckyanne3

Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.

Answers: 1

continue

Engineering, 04.07.2019 18:20, karatsgrande3772

Determine the damped natural frequencies and the steady state response of a decoupled damped forced two degrees of freedom system. 10ä1 + 2q1 20q1 10 cos t; 10q2 +4q2 + 40q2 10 cos t

Answers: 3

continue

Engineering, 04.07.2019 19:10, kelseiroll9759

Ahelical coil spring has a mean diameter of 50 mm, a wire diameter of 5.5 mm and is wound with a pitch of 10 mm. the spring steel has an ultimate strength of 1250 mpa. find the force needed to compress the spring solid and the wire stress in this condition. state whether the spring will return to its initial length.

Answers: 1

continue

Engineering, 04.07.2019 19:20, zoebtharpe

Heat transfer by is the fastest mode of heat transfer that requires no intervening medium. a)-conduction b)-convection c)-radiation d)-conduction and convection

Answers: 1

continue

You know the right answer?

Kirchoff's Law states that, by the time current has returned to its source, all
must be used