Engineering, 03.03.2020 23:16 tatemelliott

This assignment covers the sequential circuit component: Register and ALU. In this assignment you are supposed to create your own storage component for two numbers using registers. Those two numbers are then passed into a custom ALU that calculates the result of one of four possible operations. Key aspect of this assignment is to understand how to control registers, how to route signals and how to design a custom ALU.

Answers: 2

Show answers

Answers

Answer from: happy121906

The part I called command in the first diagram has been renamed to opcode, or operation code. This is a set of bits (a number) that will tell the ALU which action to perform. I can get the LC-3 opcodes for ADD and NOT and ADD from the book, so I'm not too worried.

Note the #? comment by the switch above opcode. This means I'm not sure how many switches I will need. How many bits do I need to perform all the operations I want? The textbook will tell me.

Materials

Now I make a list of all the materials you have accumulated so far. This list is just an example; yours may be different.

Two 4-bit inputs

One 4-bit output

Two keypads for 4-bit input

Three 7-segment displays (2 for input, 1 for output)

A bunch of switches for opcode (could use a keypad, I guess, but switches are so much more geeky)

A bunch of lights too

The "is zero" LED

One button for clock

One button for reset

One switch for carry-in

Include logic to perform a SUB instruction. That is, subtract the second operand from the first (out = in1 - in2). All three values -- both inputs and the output -- must be two's complement numbers (negative numbers must be represented). Your design may work in one (8 points) or two (4 points) clock cycles.

Explanation:

You are allowed to use the Logisim built-in registers.

The clear input of the register should not be used (do not connect anything to

them).

Custom ALU

Use the provided subcircuit in the template to implement your ALU. You do not have to create additional subcircuits to do this. The ALU has a total of three inputs: First number, second number and select operation input. And one output: Result. The first and second number are used as input for the operations the ALU performs. The select input decides which operation result will be on the single output of the ALU. The ALU is supposed to calculate: NumberA OPERATION NumberB. Register 1 of the storage contains NumberA and Register 2 contains NumberB. The ALU must be able to compute signals with a 4-bit width. Make sure to add labels to all inputs and outputs.

The following operations should be performed for each select input combination (s1s0): • 00: Logic Bitwise XOR

• 01: Multiplication

• 10: Division

• 11: Addition Notes:

You can change the inputs bit width / data bits of any gate to more that 1-bit.

The Logic Bitwise XOR operation can be done with a single XOR gate.

You are also allowed to use the built-in arithmetic logic components and multi- plexer provided by Logisim.

If the result is larger than 4 bits, it will be truncated (only 4 LSB will be shown). This behavior is intended for this assignment. Also, negative results do not have to be considered.

Once you have implemented the ALU circuit, connect the wires in the main circuit properly and test all four operations of your ALU in combination with the storage component.

Answer from: Quest

angvrswer:

vfg

grfhrtrhr:

jjj

yjujuju

jujuhuyhyt

bgf

bgr

gbr

bgr

gtr

bgr

gbgbbg

bgg

bbg

bfg

dcwf

fdb

ggb

rfe

gtg

gegte

gff

dfg

gfdsax

cvfbgnh

jmhngf

dsaazxscvb

nmhgb

fvdcsxaz

zxcv

bghn

Answer from: Quest

answer:

i dont know but you should start brainstorming ideas like how would you post them

explanation:

Other questions on the subject: Engineering

Engineering, 03.07.2019 15:10, margaret1758

If you were designing a bumper for a car, would you prefer it to exhibit elastic or plastic deformation? why? consider the functions of a bumper in both a minor "fender-bender" and a major collision.

Answers: 1

continue

Engineering, 04.07.2019 18:10, mm016281

What difference(s) did you notice using a pneumatic circuit over hydraulic circuit. explain why the pneumatic piston stumbles when it hits an obstacle.

Answers: 2

continue

Engineering, 04.07.2019 18:10, meganwintergirl

Afour cylinder four-stroke in-line engine has a stroke of 160mm, connecting rod length of 150mm, a reciprocating mass of 3kg and its firing order is 1-3-4-2. the spacing between cylinders is 100mm. i. show that the engine is in balance with regard to the primary inertia forces and primary 3. a and secondary inertia couples. li determine the out of balance secondary inertia force ii. propose ways of balancing this out of balance force and discuss the challenges that will arise

Answers: 3

continue

Engineering, 04.07.2019 18:10, sarahgrindstaff123

Afluid flows with a velocity field given by v=(x/t)i.. determine the local and convective accelerations when x=3 and t=1.

Answers: 2

continue

You know the right answer?

This assignment covers the sequential circuit component: Register and ALU. In this assignment you ar...