![subject](/tpl/images/cats/User.png)
Engineering, 21.02.2020 03:41 ahnaodoido384
This is problem 4 from chapter 6 of the course text. Find the Thevenin equivalent seen at the terminal A-B. Select which answer below provides the correct Vs and resistance Rth of the Thevenin equivalent.
Vs1 12V
Is2 0.4A
R1 60ohms
R2 60ohms
R3 40ohms
A) Vs = 3V, Rth = 160 Ohm
B) Vs = -3V, Rth = 160 Ohm
C) Vs = 9V, Rth = 30 Ohm
D) Vs = -9V, Rth = 30 Ohm
E) Vs = 3V, Rth = 30 Ohm
F) Vs = -3V, Rth = 30 Ohm
G) Vs = 9V, Rth = 120/7 Ohm
H) Vs = -9V, Rth = 120/7 Ohm
![ansver](/tpl/images/cats/User.png)
Answers: 3
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Other questions on the subject: Engineering
![image](/tpl/images/cats/User.png)
Engineering, 03.07.2019 15:10, breannaasmith1122
Two flowing streams of argon gas are adiabatically mixed to form a single flow/stream. one stream is 1.5 kg/s at 400 kpa and 200 c while the second stream is 2kg/s at 500 kpa and 100 ? . it is stated that the exit state of the mixed single flow of argon gas is 150 c and 300 kpa. assuming there is no work output or input during the mixing process, does this process violate either the first or the second law or both? explain and state all your assumptions.
Answers: 1
![image](/tpl/images/cats/User.png)
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, QueenLife4869
Awall of 0.5m thickness is to be constructed from a material which has average thermal conductivity of 1.4 w/mk. the wall is to be insulated with a material having an average thermal conductivity of 0.35 w/mk so that heat loss per square meter shall not exceed 1450 w. assume inner wall surface temperature of 1200°c and outer surface temperature of the insulation to be 15°c. calculate the thickness of insulation required.
Answers: 3
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, 0436500
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
You know the right answer?
This is problem 4 from chapter 6 of the course text. Find the Thevenin equivalent seen at the termin...
Questions in other subjects:
![Konu](/tpl/images/cats/fizika.png)
![Konu](/tpl/images/cats/mat.png)
Mathematics, 29.11.2021 09:50
![Konu](/tpl/images/cats/mat.png)
Mathematics, 29.11.2021 09:50
![Konu](/tpl/images/cats/mat.png)
Mathematics, 29.11.2021 09:50
![Konu](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 29.11.2021 09:50
![Konu](/tpl/images/cats/en.png)
![Konu](/tpl/images/cats/mat.png)
Mathematics, 29.11.2021 09:50
![Konu](/tpl/images/cats/en.png)
English, 29.11.2021 09:50
![Konu](/tpl/images/cats/mat.png)
Mathematics, 29.11.2021 09:50