Engineering, 19.02.2020 21:00 LilFlamingo247

The alignment readings for the front of a vehicle are shown above. Camber and toe are within specification, caster is not. Technician A says that with the current settings, the left front tire tread may wear on the inside edge. Technician B says that with the current settings, the vehicle may pull to the left. Who is right? A. A only B. B only C. Both A and B D. Neither A nor B

Answers: 3

Show answers

Answers

Answer from: hardwick744

B. B only

Given Information:

1. Camber and toe are within specification

2. Caster is not within specification

Technician A says that with the current settings, the left front tire tread may wear on the inside edge.

Technician B says that with the current settings, the vehicle may pull to the left

Explanation:

Lets discuss the effects of Camber, toe and caster misalignment

Effects of Camber and Toe misalignment:

Camber is the inward or outward tilt of the fron tires and is used to distribute load across the tread. Any misalignment causes uneven loading on the tires which results in tire wear on one edge.

The most common cause of tire wear on the inside edge is due to the camber misalignment which results in premature tire wear.

Another reason is of tire wear is vehicle’s toe. A slight misalignment of the toe reduces the life of the tire.

Since it is given that camber settings and toe settings are within specification therefore, tire tread wear on the inside edge cannot happen if camber and toe are within specification.

Technician A cannot be right.

Effects of Caster misalignment:

Whenever there is a misalignment of the castor then the vehicle will not be able to go in straight line rather it will pull to either left or right side. Caster misalignment also causes heavy or light steering depending upon the positive or negative misalignment of caster.

Since it is given that caster settings are not within specification therefore, the vehicle may pull to the left due to the caster misalignment.

Technician B must be right.

Answer from: Quest

unlike the threaded fasteners which are used to clamp the machine members, power screws are used to transmit power. common applications of power screws are: screw jacks: to lift weight. lead screw of lathe: for axial movement of tool and its precise positioning.

Answer from: Quest

answer:

uygtfjyftujtfj

explanation:

Other questions on the subject: Engineering

Engineering, 03.07.2019 14:10, BardiFan

Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.

Answers: 3

continue

Engineering, 04.07.2019 18:10, leomessifanboy678

The filament of an incandescent lamp has a temperature of 2000k. calculate the fraction of radiation emitted in the visible light band if the filament is approximated as blackbody

Answers: 2

continue

Engineering, 04.07.2019 18:10, juansoto227711

Journeyman training is usually related (clo2) a)-to specific tasks b)-to cost analysis of maintenance task c)-to control process to ensure quality d)-to installation of machinery

Answers: 2

continue

Engineering, 04.07.2019 18:20, rhussein6452

Wiy doeres rere okhn a pump whon working betwon the same pressure range?

Answers: 2

continue

You know the right answer?

The alignment readings for the front of a vehicle are shown above. Camber and toe are within specifi...