Engineering, 17.02.2020 22:23 ijohnh14

Define the following terms in your own words: (a) elastic strain, (b) plastic strain, (c) creep strain, (d) tensile viscosity, (e) recovery, and (f) relaxation.

Answers: 3

Show answers

Answers

Answer from: kps26pd2mea

Detailed Answer is given below,

Explanation:

(a) Elastic strain

Elastic deformation is defined as the limit for the deformation values up to which the object will bounce and return to the original shape when the load is removed.

When the object is subjected to an external load, it deforms. If the load exceeds the load corresponding to the elastic limit of the object, then, after removing the load, the object cannot return to its original geometric specification.

(b) Plastic strain

Plastic Strain is a deformation that cannot be recovered after eliminating the deforming force. In other words, if the applied tension is greater than the elastic limit of the material, there will be a permanent deformation.

The deformation of the material at a higher temperature is much more than at the normal temperature known as creep.

Subsequently, the deformation produced in heated material is called creep deformation. Creep deformation is a function of temperature.

(d) Tensile viscosity

Viscosity is a main parameter when measuring flux fluids, such as liquids, semi-solids, gases and even solids. Brookfield deals with liquids and semi-solids. Viscosity measurements are made together with the quality and efficiency of the product. Any person involved in the characterization of the flow, in research or development, quality control or transfer of fluids, at one time or another is involved with some kind of viscosity measurement.

(e) Recovery

Recovery is a process whereby deformed grains can reduce their stored energy by eliminating or reorganizing defects in their crystalline structure. These defects, mainly dislocations, are introduced by plastic deformation of the material and act to increase the elastic limit of a material.

(f) Relaxation

Stress relaxation occurs in polymers when they remain tense for long periods of time.

These alloys have very good resistance to stress relaxation and, therefore, are used as spring materials.

Stress relaxation is a gradual reduction of stress over time in constant tension.

Answer from: Quest

answer:

look in settings

explanation:

Answer from: Quest

answer:

(b)

explanation:

Other questions on the subject: Engineering

Engineering, 03.07.2019 14:10, kayabwaller4589

When at a point two solid phase changes to one solid phase on cooling then it is known as a) eutectoid point b) eutectic point c) peritectic point d) peritectoid point

Answers: 3

continue

Engineering, 03.07.2019 14:10, volleyballfun24

If the thermal strain developed in polyimide film during deposition is given as 0.0044. assume room temperature is kept at 17.3 c, and thermal coefficient of expansion for the film and the substrate are 54 x 10^-6c^-1 and 3.3 x 10^-6c^-1respectively. calculate the deposition temperature.

Answers: 3

continue

Engineering, 03.07.2019 15:10, breannaasmith1122

Two flowing streams of argon gas are adiabatically mixed to form a single flow/stream. one stream is 1.5 kg/s at 400 kpa and 200 c while the second stream is 2kg/s at 500 kpa and 100 ? . it is stated that the exit state of the mixed single flow of argon gas is 150 c and 300 kpa. assuming there is no work output or input during the mixing process, does this process violate either the first or the second law or both? explain and state all your assumptions.

Answers: 1

continue

Engineering, 04.07.2019 03:10, lauriepdx17

What precautions should you take to prevent injuries when dealing with heavy loads?

Answers: 1

continue

You know the right answer?

Define the following terms in your own words: (a) elastic strain, (b) plastic strain, (c) creep stra...