Engineering, 27.12.2019 06:31 bendlogan2687

A3-phase induction motor with 4 poles is being driven at 45 hz and is running in its normal operating range. when connected to a certain load, the motor rotates at a speed of 1070 rpm and outputs 800w a. what is the slip and developed torque? b. what is the new slip and motor speed if the developed torque is reduced to 4 nm?

Answers: 2

Show answers

Answers

Answer from: emily200705

a) The slip for the given conditions is 0.2074 or 20.74% and the developed torque is 7.14 Nm.

b) The new slip after reducing the torque to 4 Nm is 0.1162 or 11.62% and the new motor speed is 1193.13 rpm.

Explanation:

In order to find the slip we can use the definition as the relative difference between Synchronous speed and the rotor speed and that the developed torque is the ratio between output power and rotor angular velocity.

Slip.

We can find the synchronous speed u sing the following formula

$N_s =\cfrac{120f}p$

Where f stands for the frequency and p the number of poles, so we have

$N_s = \cfrac{120(45)}{4}\\N_s =1350 \,rpm$

Replacing on the slip formula

$S = \cfrac{N_s-N_r}{N_s}$

we get

$S = \cfrac{1350-1070}{1350}\\ S = 0.2074$

Thus the slip for the given conditions is 0.2074 or 20.74%.

Developed torque.

We can find the angular velocity in radians per second

$\omega_r =1070 \cfrac{rev}{min} \times \cfrac{1 \, min}{60 \, s}\times \cfrac{2\pi rad}{1 \, rev}\\\omega_r =112.05 \, \cfrac{rad}{s}$

Thus we can replace on the torque formula

$\tau = \cfrac{P}{\omega_r}\\\tau=\cfrac{800 W}{112.05 \, \cfrac{rad}{s}}$

We get

$\tau = 7.14\, N m$

The developed torque is 7.14 Nm.

Slip for the reduced torque.

The torque is proportional to the slip, so we can write

$\cfrac{\tau_1}{\tau_2}= \cfrac{S_1}{S_2}$

Thus solving for the new slip S_2 we have:

$S_2 = S_1 \cfrac{\tau_2}{\tau_1}$

Replacing the values obtained on the previous part we have

$S_2 = 0.2074 \cfrac{4 Nm}{7.14 Nm}\\ S_2=0.1162$

So the new slip after reducing the torque to 4 Nm is 0.1162 or 11.62%

Motor speed.

We can use the slip definition

$S_2 =\cfrac{N_s-N_{r_2}}{N_s}$

Solving for the motor speed we have

$S_2N_s =N_s-N_{r_2}$

$N_{r_2}=N_s-S_2N_s \\N_{r_2}=N_s(1-S_2)$

Replacing values we have

$N_{r_2}=1350 \, rpm(1-0.1162)\\N_{r_2}=1193.13 rpm$

The new motor speed is 1193.13 rpm.

Answer from: Quest

the warning light flashes for a second or two when the engine starts. if it stays on, there's must be something wrong with the coolant. you should never dare to continue driving when the light is on. pull over as soon as possible and shut the engine off.

hope this is what you're talking about

Answer from: Quest

answer:

explanation:

assault rifle is a rapid-fire, magazine-fed rifle designed for military use. it is a shoulder-fired weapon that allows the shooter to select between semi-automatic (requiring you pull the trigger for each shot), fully automatic (hold the trigger and the gun continuously fires) or three-shot-burst modes.

Other questions on the subject: Engineering

Engineering, 03.07.2019 14:10, bryneosburn

Line joining liquid phase with liquid and solid phase mixture is known as: a) liquidus b) solidus c) tie line d) none of the mentioned

Answers: 2

continue

Engineering, 04.07.2019 16:10, TheOriginalMeyah

An electrical motor raises a 50kg load at a construct velencity .calculate the power of the motor, if it takes 40sec to raise the load through a height of 24m(take g =9.8n/g)

Answers: 2

continue

Engineering, 04.07.2019 18:10, ayoismeisjjjjuan

Manometers are good examples of measuring instruments, nowadays they are not as common as before. a)-capacitive probe gauges b)-gravitational gauges deformation ) gauges d)-digital gauges

Answers: 1

continue

Engineering, 04.07.2019 19:10, nani3906

Starting wih an energy balance on a rectangular volume element, derive the one- dimensional transient heat conduction equation for a plane wall with constant thermal conductivity and no heat generation.

Answers: 1

continue

You know the right answer?

A3-phase induction motor with 4 poles is being driven at 45 hz and is running in its normal operatin...