subject
Engineering, 05.12.2019 21:31 estherdinhllama

The popularity of orange juice, especially as a breakfast drink, makes this beverage an important factor in the economy of orange-growing regions. most marketed juice is concentrated and frozen and then reconstituted before consumption, and some is "not-from-concentrate." although concentrated juices are less popular in the united states than they were at one time, they still have a major segment of the market for orange juice. the approaches to concentrating orange juice include evaporation, freeze concentration, and reverse osmosis. here we examine the evaporation process by focusing only on two constituents in the juice solids and water. fresh orange juice contains approximately 10 wt% solids (sugar, citric acid, and other ingredients) and frozen concentrate contains approximately 42 wt% solids. the frozen concentrate is obtained by evaporating water from the fresh juice to produce a mixture that is approximately 65 wt% solids. however, so that the flavor of the concentrate will closely approximate that of fresh juice, the concentrate from the evaporator is blended with fresh orange juice (and other additives) to produce a final concentrate that is approximately 42 wt% solids. (a) label the flowchart of this process, neglecting the vaporization of everything in the juice but water first prove that the subsystem containing the point where the bypass stream splits off from the evaporator feed has one degree of freedom. (if you think it has zero degrees, try determining the unknown variables associated with this system.) then perform the degree-of freedom analysis for the overall system, the evaporator, and the bypass-evaporator product mixing point, and write in order the equations you would solve to determine all unknown stream variables. in each equation, circle the variable for which you would solve, but don't do any calculations. (b) calculate the amount of product (42% concentrate) produced per 100 kg fresh juice fed to the process and the fraction of the feed that bypasses the evaporator. bypass mising point evaporator

ansver
Answers: 1

Other questions on the subject: Engineering

image
Engineering, 04.07.2019 18:10, niicoleassssssf
Aflywheel accelerates for 5 seconds at 2 rad/s2 from a speed of 20 rpm. determine the total number of revolutions of the flywheel during the period of its acceleration. a.5.65 b.8.43 c. 723 d.6.86
Answers: 2
image
Engineering, 04.07.2019 18:10, keigleyhannah30
Aplate clutch has a single pair of mating friction surfaces 250-mm od by 175-mm id. the mean value of the coefficient of friction is 0.30, and the actuating force is 4 kn. a) find the maximum pressure and the torque capacity using the uniform-wear model. b) find the maximum pressure and the torque capacity using the uniform-pressure model.
Answers: 3
image
Engineering, 04.07.2019 18:20, dlr1628
Acertain flow of air (at stp) has a velocity distribution given by v i (in ft/s). if this flow is going through a 4 ft square area in the yz-plane (centered at the origin), what is the mass flow rate (in lbm/s)?
Answers: 2
image
Engineering, 04.07.2019 18:20, AnonymousLizard52303
A2-m rigid tank initially contains saturated water vapor at 100 kpa. the tank is connected to a supply line through a valve. steam is flowing in the supply line at 600 kpa and 300 c. the valve is opened, and steam is allowed to enter the tank until the pressure in the tank reaches the line pressure, at which point the valve is closed. a thermometer placed in the tank indicates that the temperature at the final state is 200°c. determine (a) the mass of steam that has entered the tank (b) the amount of heat transfer.
Answers: 3
You know the right answer?
The popularity of orange juice, especially as a breakfast drink, makes this beverage an important fa...

Questions in other subjects:

Konu
History, 17.10.2021 05:20
Konu
History, 17.10.2021 05:20
Konu
English, 17.10.2021 05:20
Konu
Mathematics, 17.10.2021 05:20