Engineering, 22.11.2019 06:31 taniyahreggienae

An overflow ogee crest for a spillway is to discharge 20,000 cfs. the upstream face of the crest is sloped 1: 1 and a bridge is to span the crest. flow over the spillway is to be controlled by a series of tainter gates. bridge piers 18-in wide (pier contraction kp = 0.05) with rounded noses are to be provided to support the gates. the bridge spans (center to center of piers) are not to exceed 30 ft. the maximum expected head he = 10 ft. neglect velocity of approach head. the distance from the spillway crest to the reservoir bottom p = 18 ft. the abutment coefficient ka = 0.10. assume that your design head is equal to the maximum expected head. determine: (ans: l’ = 169.4-ft,) (a) the crest length required (b) the number of tainter gates to be used (c) the width of each gate

Answers: 1

Show answers

Other questions on the subject: Engineering

Engineering, 03.07.2019 14:10, BardiFan

Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.

Answers: 3

continue

Engineering, 03.07.2019 15:10, breannaasmith1122

Two flowing streams of argon gas are adiabatically mixed to form a single flow/stream. one stream is 1.5 kg/s at 400 kpa and 200 c while the second stream is 2kg/s at 500 kpa and 100 ? . it is stated that the exit state of the mixed single flow of argon gas is 150 c and 300 kpa. assuming there is no work output or input during the mixing process, does this process violate either the first or the second law or both? explain and state all your assumptions.

Answers: 1

continue

Engineering, 04.07.2019 18:10, bckyanne3

Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.

Answers: 1

continue

Engineering, 04.07.2019 18:10, kevin72836

Consider a large isothermal enclosure that is maintained at a uniform temperature of 2000 k. calculate the emissive power of the radiation that emerges from a small aperture on the enclosure surface. what is the wavelength ? , below which 10% of the emission is concentrated? what is the wavelength ? 2 above which 10% of the emission is concentrated? determine the wavelength at which maximum spectral emissive power occurs. what is the irradiation incident on a small object placed inside the enclosure?

Answers: 2

continue

You know the right answer?

An overflow ogee crest for a spillway is to discharge 20,000 cfs. the upstream face of the crest is...