subject
Engineering, 20.11.2019 23:31 RyannLambertt7141

Two carts of mass ma and mb are free to roll on a straight horizontal track. initially, the velocities of the carts are vai ˆı and vbi ˆı, with vai > vbi. because of this last inequality, the two carts will collide. the coefficient of restitution for the collision is e1. given ma, mb, vai, vbi, and e, find the horizontal components of velocity, vaf , vbf after impact.2. for each set of parameter values listed below, calculate numerical values for final velocity components vaf and vbf , as well as kinetic energy before impact and kinetic energy after impact. what percentage of the initial kinetic energy is lost during the impact? (a) ma = 1 mg, mb = 5 mg, vai = 10 m/s, vbi = 0, e = 0.5.(b) ma = 5 mg, mb = 1 mg, vai = 10 m/s, vbi = 0, e = 0.5.(c) ma = 5 mg, mb = 1 mg, vai = 10 m/s, vbi = 0, e = 1.0.(d) ma = 3 mg, mb = 3 mg, vai = 10 m/s, vbi = 0, e = 1.0.(e) ma = 4 mg, mb = 3 mg, vai = 10 m/s, vbi = 5 m/s, e = 1.0.

ansver
Answers: 3

Other questions on the subject: Engineering

image
Engineering, 04.07.2019 08:10, doggo242
Which of the following is an easy way to remember the modified “x” tire rotation? a. nondrive wheels straight, cross the drive wheels b. drive wheels straight, cross the nondrive wheels c. drive wheels crossed, nondrive wheels straight d. drive wheels crossed, nondrive wheels crossed
Answers: 1
image
Engineering, 04.07.2019 18:10, alyssabailey7545
Give heat transfer applications for the following, (i) gas turbines (propulsion) ) gas turbines (power generation). (iii) steam turbines. (iv) combined heat and power (chp). (v) automotive engines
Answers: 1
image
Engineering, 04.07.2019 18:10, bckyanne3
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
image
Engineering, 04.07.2019 18:20, miguel454545
Along 8-cm diameter steam pipe whose external surface temperature is 900c connects two buildings. the pipe is exposed to ambient air at 70c with a wind speed of 50 km/hr blowing across the pipe. determine the heat loss from the pipe per unit length. (b) air at 500c enters a section of a rectangular duct (15 cm x 20 cm) at an average velocity of 7 m/s. if the walls of the duct are maintained at 100c. a) the length of the tube for an exit temperature of the air to be 40 0c. b)the rate of heat transfer from the air. c) the fan power needed to overcome the pressure drop in this section of the duct.
Answers: 1
You know the right answer?
Two carts of mass ma and mb are free to roll on a straight horizontal track. initially, the velociti...

Questions in other subjects:

Konu
Mathematics, 22.10.2020 18:01
Konu
Mathematics, 22.10.2020 18:01
Konu
Mathematics, 22.10.2020 18:01