![subject](/tpl/images/cats/User.png)
Engineering, 08.11.2019 04:31 jeffylovesgreenbeans
Ahydraulic press is powered by a remote high-pressure pump. the gage pressure at the pump is 20 mpa, and the pressure required to operate the press is 19mpa (gage) at a flow rate of 0.032 m3/min. the press and pump are to be connected by 100 m of drawn stainless steel tubing. the fluid properties are as follows: µ=50 cp, sg = 0.90. what is the minimum tubing diameter that can be used? what commercial steel pipe nominal size is suitable for this purpose if schedule number is 80?
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Other questions on the subject: Engineering
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, bckyanne3
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, salazjlove
Which of the following refers to refers to how well the control system responds to sudden changes in the system. a)-transient regulation b)- distributed regulation c)-constant regulation d)-steady-state regulation
Answers: 1
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20, maustin5323
Athin walled concentric tube exchanger is used to cool engine oil from 160°c to 60°c with water that is available at 25°c acting as a coolant. the oil and water flow rates are each at 2 kg/s, and the diameter of the inner tube is 0.5 m and the corresponding value of the overall heat transfer coefficient is 250 w/m2. oc. how long must the heat exchanger be to accomplish the desired cooling? cpwater=4.187 kj/kg-candcpengine el=2.035 kj/kg·°c, oil . 120]
Answers: 1
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20, esmemaluma00
Find the minimum film thickness for a journal bearing with the data below. shaft diameter, d-50 mm, clearance ratio, cdratio? 0.001, shaft speed, n 2000 rpm; bearing length. i 200 mm; eccentricity ration, ? -0.55. ( note, cdratio-ca/d) the minimum film thickness is um
Answers: 2
You know the right answer?
Ahydraulic press is powered by a remote high-pressure pump. the gage pressure at the pump is 20 mpa,...
Questions in other subjects:
![Konu](/tpl/images/cats/istoriya.png)
History, 13.10.2019 10:20
![Konu](/tpl/images/cats/en.png)
![Konu](/tpl/images/cats/en.png)
![Konu](/tpl/images/cats/istoriya.png)
History, 13.10.2019 10:20
![Konu](/tpl/images/cats/mat.png)
![Konu](/tpl/images/cats/obshestvoznanie.png)
![Konu](/tpl/images/cats/en.png)
![Konu](/tpl/images/cats/obshestvoznanie.png)
![Konu](/tpl/images/cats/health.png)
Health, 13.10.2019 10:20