subject
Engineering, 30.09.2019 20:30 tinajackson6534

Avery long, very thin straight line has a uniform charge per unit length of λ, where λ > 0. it is surrounded by a long, cylindrical, insulating plastic shell, which has an inner radius a and outer radius b. the line lies along the central axis of the cylindrical shell. the cylindrical shell has a uniform volume charge density rho, where rho > 0. (both the line and the shell are long enough to approximate them as infinitely long.) find the electric field in the following regions by choosing a gaussian cylinder of radius r and length l. (use any variable or symbol stated above along with the following as necessary: ε0.) (a) r < a magnitude e = incorrect: your answer is incorrect. how much charge is enclosed by the gaussian cylinder? how is the enclosed charge related to the charge per unit length? what is the direction of the electric field? what is the area of the gaussian cylindrical surface? direction (b) a < r < b magnitude e = direction (c) r > b magnitude e = direction (d) what if? suppose we have the same situation as described above, where again λ > 0, but now rho can be any value. for what value of rho will there be zero electric field for r > b? rho =

ansver
Answers: 1

Other questions on the subject: Engineering

image
Engineering, 04.07.2019 18:10, koolgurl2003
Apump is used to circulate hot water in a home heating system. water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. the inlet pressure and temperature are 14.7 lbf/in.2, and 180°f, respectively; at the exit the pressure is 60 lbf/in.2 the pump requires 1/15 hp of power input. water can be modeled as an incompressible substance with constant density of 60.58 lb/ft3 and constant specific heat of 1 btu/lb or. neglecting kinetic and potential energy effects, determine the temperature change, in °r, as the water flows through the pump.
Answers: 1
image
Engineering, 04.07.2019 18:10, niyawilliams23
Asingle-geared blanking press has a stroke of 200 mm and a rated capacity of 320 kn. a cam driven ram is assumed to be capable of delivering the full press load at constant force during the last 15 percent of a constant-velocity stroke. the camshaft has an average speed of 90 rev/min and is geared to the flywheel shaft at a 6: 1 ratio. the total work done is to include an allowance of 16 percent for friction a) estimate the maximum energy fluctuation b) find the rim weight for an effective diameter of 1.2 m and a coefficient of speed fluctuation of 0.10
Answers: 1
image
Engineering, 04.07.2019 18:10, lowkeyqueenk
Apipe with an outside diameter of 15 cm is exposed to an ambient air and surrounding temperature of -20°c. the pipe has an outer surface temperature of 65°c and an emissivity of 0.85. if the rate of heat loss from the pipe surface is 0.95 kw per meter of length, the external convective heat transfer coefficient (h) is: (a) 12.5 w/m"k (b) 18.6 w/mk (c) 23.7 w/mk (d) 27.9 w/mk (e) 33.5 w/mk
Answers: 1
image
Engineering, 04.07.2019 18:10, samanthabutryn
Which one from below is not one of the reasons of planning failures? (clo3) a)-planner is careless. b-planner spend less time in the field but more time on the desk c)-planner is not qualified d)-planner does not have sufficient time to properly plan
Answers: 3
You know the right answer?
Avery long, very thin straight line has a uniform charge per unit length of λ, where λ > 0. it i...

Questions in other subjects: