subject
Engineering, 07.08.2019 19:20 TerronRice

A50-mm-diameter, thin-walled metal pipe covered with a 25-mm-thick layer of insulation (0.085 w/m k) and carrying superheated steam at atmospheric pressure is suspended from the ceiling of a large room. the steam temperature entering the pipe is 120°c, and the air temperature in the room is 20°c. the convection heat transfer coefficient on the outer surface of the covered pipe is 10 w/m2 k. the velocity of the steam in the pipe is 10 m/s. the steam temperature at the outlet of the pipe is at tmo =106°c 1. calculate the mass flow rate of steam in the pipe. 2 calculate the total ua for the entire pipe 3 calculate the internal heat transfer coefficient hi 4 construct a resistance model and calculate the resistances “r” that affect the heat transfer from the steam to the outside air. 5 calculate the length of the pipe. 6 calculate the temperature of the pipe's surface at the exit of the pipe (tso) using the resistance model at the outlet of the pipe. 7 what would happen if tmo was cooler than 106°c?

ansver
Answers: 2

Other questions on the subject: Engineering

image
Engineering, 03.07.2019 14:10, aliceohern
The y form of iron is known as: a) ferrite b) cementite c) perlite d) austenite
Answers: 3
image
Engineering, 04.07.2019 18:10, skpdancer1605
Ariver flows from north to south at 8 km/h. a boat is to cross this river from west to east at a speed of 20 km/h (speed of the boat with respect to the earth/ground). at what angle (in degrees) must the boat be pointed upstream such that it will proceed directly across the river (hint: find the speed of the boat with respect to water/river)? a 288 b. 21.8 c. 326 d. 30.2
Answers: 3
image
Engineering, 04.07.2019 18:10, DestyHilBan1183
Adouble-strand no. 60 roller chain is used to transmit power between a 13-tooth driving sprocket rotating at 300 rev/min and a 52-tooth driven sprocket. a) what is the allowable horsepower of this drive? b) estimate the center-to-center distance if the chain length is 82 pitches. c) estimate the torque and bending force on the driving shaft by the chain if the actual horsepower transmitted is 30 percent less than the corrected (allowable) power.
Answers: 3
image
Engineering, 04.07.2019 18:20, maciemarklin79981
A3-mm-thick panel of aluminum alloy (k 177 w/m-k, c 875 j/kg-k and ? = 2770 kg/m) is finished on both sides with an epoxy coating that must be cured at or above t,-150°c for at least 5 min. the production line for the curing operation involves two steps: (1) heating in a large oven with air at ts,0-175°c and a convection coefficient of h, 40 w/m2. k, and (2) cooling in a large chamber with air at 25°c and a con- vection coefficient of he 10 w/m2.k. the heating portion of the process is conducted over a time interval te which exceeds the ime required to reach 150°c by 5 min (h = r + 300 s). the coating has an emissivity of ? = 0.8, and the temperatures of the oven and chamber walls are 175 and 25°c, respectively. if the panel is placed in the oven at an initial temperature of 25°c and removed from the chamber at a safe-to-touch tempera ture of 37°c, what is the total elapsed time for the two-step curing operation?
Answers: 3
You know the right answer?
A50-mm-diameter, thin-walled metal pipe covered with a 25-mm-thick layer of insulation (0.085 w/m k)...

Questions in other subjects:

Konu
Social Studies, 24.02.2022 19:10
Konu
Arts, 24.02.2022 19:10
Konu
Mathematics, 24.02.2022 19:10