Engineering, 19.07.2019 21:20 niharikam242

Air at 293k and 1atm flow over a flat plate at 5m/s. the plate is 5m wide and 6m long. (a) determine the boundary layer thickness 1m from the leafing edge. (b) determine the critical distance xc from the leading edge. if transition occur at a reynold number of 1(c) repeat part (a) 3m from leading edge (d) find the force exerted on the section of the plate where the flow is laminar (e) determine the force exerted one one side of the entire plate

Answers: 3

Show answers

Answers

Answer from: thatkiddarius539

a). 8.67 x $10^{-3}$ m

b).0.3011 m

c).0.0719 m

d).0.2137 N

e).1.792 N

Explanation:

Given :

Temperature of air, T = 293 K

Air Velocity, U = 5 m/s

Length of the plate is L = 6 m

Width of the plate is b = 5 m

Therefore Dynamic viscosity of air at temperature 293 K is, μ = 1.822 X $10^{-5}$ Pa-s

We know density of air is ρ = 1.21 kg / $m^{3}$

Now we can find the Reyonld no at x = 1 m from the leading edge

Re = $\frac{\rho .U.x}{\mu }$

Re = $\frac{1.21 \times 5\times 1}{1.822\times 10^{-5} }$

Re = 332052.6

Therefore the flow is laminar.

Hence boundary layer thickness is

δ = $\frac{5.x}{\sqrt{Re}}$

= $\frac{5\times 1}{\sqrt{332052.6}}$

= 8.67 x $10^{-3}$ m

a). Boundary layer thickness at x = 1 is δ = 8.67 X $10^{-3}$ m

b). Given Re = 100000

Therefore the critical distance from the leading edge can be found by,

Re = $\frac{\rho .U.x}{\mu }$

100000 = $\frac{1.21\times5\times x}{1.822 \times10^{-5}}$

x = 0.3011 m

c). Given x = 3 m from the leading edge

The Reyonld no at x = 3 m from the leading edge

Re = $\frac{\rho .U.x}{\mu }$

Re = $\frac{1.21 \times 5\times 3}{1.822\times 10^{-5} }$

Re = 996158.06

Therefore the flow is turbulent.

Therefore for a turbulent flow, boundary layer thickness is

δ = $\frac{0.38\times x}{Re^{\frac{1}{5}}}$

= $\frac{0.38\times 3}{996158.06^{\frac{1}{5}}}$

= 0.0719 m

d). Distance from the leading edge upto which the flow will be laminar,

Re = $\frac{\rho \times U\times x}{\mu }$

5 X $10^{5}$ = $\frac{1.21 \times 5\times x}{1.822\times 10^{-5}}}$

x = 1.505 m

We know that the force acting on the plate is

$F_{D}$ = $\frac{1}{2}\times C_{D}\times \rho \times A\times U^{2}$

and $C_{D}$ at x= 1.505 for a laminar flow is = $\frac{1.328}{\sqrt{Re}}$

= $\frac{1.328}{\sqrt{5\times10 ^{5}}}$

= 1.878 x $10^{-3}$

Therefore, $F_{D}$ = $\frac{1}{2}\times C_{D}\times \rho \times A\times U^{2}$

= $\frac{1}{2}\times 1.878\times 10^{-3}\times 1.21\times (5\times 1.505)\times 5^{2}$

= 0.2137 N

e). The flow is turbulent at the end of the plate.

Re = $\frac{\rho \times U\times x}{\mu }$

= $\frac{1.21 \times 5\times 6}{1.822\times 10^{-5} }$

= 1992316

Therefore $C_{D}$ = $\frac{0.072}{Re^{\frac{1}{5}}}$

= $\frac{0.072}{1992316^{\frac{1}{5}}}$

= 3.95 x $10^{-3}$

Therefore $F_{D}$ = $\frac{1}{2}\times C_{D}\times \rho\times A\times U^{2}$

= $\frac{1}{2}\times 3.95\times 10^{-3}\times 1.21\times (5\times 6)\times 5^{2}$

= 1.792 N

Answer from: Quest

answer:

put more,

Answer from: Quest

answer:

the army does care about its soilders sir i think yout getting off on the wrong foot sir you need to respect our country were keeping the peole that want to d harm towards you out. so dont go saying we don't care cause we do

Other questions on the subject: Engineering

Engineering, 04.07.2019 18:10, lowkeyqueenk

Apipe with an outside diameter of 15 cm is exposed to an ambient air and surrounding temperature of -20°c. the pipe has an outer surface temperature of 65°c and an emissivity of 0.85. if the rate of heat loss from the pipe surface is 0.95 kw per meter of length, the external convective heat transfer coefficient (h) is: (a) 12.5 w/m"k (b) 18.6 w/mk (c) 23.7 w/mk (d) 27.9 w/mk (e) 33.5 w/mk

Answers: 1

continue

Engineering, 04.07.2019 18:20, cdyshaylia55

Water vapor initially at 10 bar and 400 °c is contained within a piston-cylinder assembly. the water lost heat to the surrounding according to isochoric (iso-volumetric) process until its temperature is 150 °c. the water is then condensed isothermally to saturated liquid. for the water as a system, calculate the work in kj/kg

Answers: 2

continue

Engineering, 04.07.2019 19:20, kaitlyn114433

Ashielded metal arc-welding operation is accomplished in a work cell by a fitter and a welder. the fitter takes 5.5 min to load components into the welding fixture at the beginning of the work cycle, and 1.5 min to unload the completed weldment at the end of the cycle. the total ength of the weld seams 1200 mm, and the travel speed used by the welder averages 300 mm/min. every 600 mm of seam length, the welding stick must be changed, which takes 0.8 min. while the fitter is working, the welder is idle (resting): and while the welder is working the fitter is idle. (a) determine the average arc-on time as a fraction of the work cycle time. (b) how much improvement in arc-on time would result if the welder used flux-cored arc welding (manually operated), given that the spool of weld wire must be changed every 10 weldments, and it takes the welder 5.0 min to accomplish the change? (c) what are the production rates for these two cases (weldments completed per hour)? attach your work and solutions.

Answers: 1

continue

Engineering, 06.07.2019 03:20, carrietaylor234

Avertical steel rod of length 2.0 m and diameter 25 mm is rigidly fixed at its upper end and has a flange at its lower, free, end. what will be the maximum stress produced in the rod when a load of 20 kn is applied, (a) gradually to the lower end, (b) suddenly to the lower end, (c) by a collar falling from a height of 50 mm on to the flange?

Answers: 3

continue

You know the right answer?

Air at 293k and 1atm flow over a flat plate at 5m/s. the plate is 5m wide and 6m long. (a) determine...