Sketch the titration curve for the titration of a generic weak base B with a strong acid. The titration reaction is B+H+⇌BH+
On the curve indicate the points that correspond to the following:
a) the equivalence point.
b) the region with maximum buffering) the point where pH = pKbd) the region where pH depends only on [B]e) the region where pH depends only on [BH+]f) the region where pH depends only on the amount of excess strong acid

Kindly check the attached picture.

Explanation:

Titration is one of the useful concept or practical in chemistry which is used in the determination of the concentration of a particular chemical specie. Without mincing words, let us dive straight into the solution to the question;

(a) Determining the equivalence point using the graph.

=> The equivalence point is the point at which there has been been "enough" addition of the acid to the base to give us the congugate acid. In the diagram showing the curve, it is the point labelled (a).

(b)The next thing is to determine the region with maximum buffering.

=> The position with the maximum buffering ranges from the point labelled (b) in the graph and it is the point when the acid and the base has been added. But the point with the maximum buffering is labeled as point (c).

(c). Determination of the point where pH = pKb.

=> The Point in which the pH = pKb is the point a

(d). The region where pH depends only on [B].

=> The starting point in the point in which the pH is dependent on the concentration of the base, [B].

(e). The region where pH depends only on [BH+].

=> This is the same point with point labelled as (a). Thus, point (a) and (e) are the same.

(f). The region where pH depends only on the amount of excess strong acid is the point labelled as (f) which is known as the post equivalence point.

but know think of it in terms of bond breaking and bond making.

h–h + h–h + o=o ==> h–o–h + h–o–h

as you can see from the diagram, theoretically, more energy is released by forming water, than was absorbed in breaking up the original hydrogen and oxygen molecules.

the energy level of the fuel + oxygen is higher than that of water.

therefore the fuel + oxygen mixture has the potential to release potential chemical energy as heat energy or, crucially, electrical energy, if the reaction can be made to go via  oxidation and reduction reactions involving electron transfer.

see this page for more details of the full  bond energy calculations

a  fuel cell  is a device to make electricity that functions like an electrical cell or battery that you supply with a fuel (liquid or gas) and an oxidant (oxidising agent, usually oxygen gas) which react together in a redox reaction (oxidation + reduction) to release energy as a flow of electrons i.e. an electrical current capable of doing useful work.

the oxidation of the fuel and the reduction of the oxidant reactions take place on electrodes (see diagram on right, all fully explained further down the page).

fuel cells essentially a device to release the chemical potential energy of combustible fuels as electrical energy  at a much lower temperature and without the flame!

so, the idea of a  hydrogen–oxygen fuel cell  is to release the energy from hydrogen reacting with oxygen, not as heat as in normal combustion in air, but as  useful electrical energy  i.e. a practical electricity supply.

hydrogen-oxygen fuel cells are much efficient than conventional power stations or batteries (e.g. zinc-carbon) because the electrical energy is directly generated from the chemical reaction between the oxidant and the fuel - there are no complications with boilers, turbines and generators.

in fossil fuel power stations, motor vehicles, coal/gas fires etc. quite a percentage of energy is lost as waste heat.

with a fuel cell there are fewer stages in producing the useful energy, so there is less opportunity to lose potentially useful energy e.g. waste heat, friction from moving parts etc.

a hydrogen–oxygen fuel cell is a non–polluting clean fuel since the only combustion product is water.

fuel cells  do not produce pollutants like carbon monoxide, sulfur dioxide and nitrogen oxides - gases you get from fossil fuel combustion in power stations or burnt road vehicles..

cars powered by fuel cells would be quite an environmental advantage in cities, where electric cars are already beginning to be significantly used in developed countries.

fuel cells could replace larger batteries which are not easily recycled and contain highly toxic metal compounds.

it would be an ideal fuel on this basis e.g. for motor vehicles, but that's not the only factor to consider!

it would be ideal if the hydrogen fuel could be manufactured by electrolysis of water e.g. using solar cells.

hydrogen can be used to power fuel cells.

it all sounds wonderful but, still technological problems to solve for large scale manufacture and distribution of 'clean' hydrogen gas or use in generating electricity and its rather an inflammable explosive gas!

explanation:

fuel cells e.g. the hydrogen-oxygen fuel electrical cell

fuel cells have to be supplied by an external source of fuel (e.g. hydrogen) and an oxidant e.g. oxygen or air.

the hydrogen or any other fuel is oxidised electrochemically inside the fuel cell to produce a potential difference i.e. a voltage capable of producing a working current.

the overall chemical reaction in a hydrogen fuel electrochemical cell involves the oxidation of hydrogen by oxygen to produce only water.

hydrogen fuel cells offer an alternative to rechargeable cells and batteries.

a fuel cell will produce a potential difference  ('voltage')  and a workable electric current until one of the reactants is used up.

hydrogen gas can be used as fuel.

it burns with a pale blue flame in air reacting with oxygen to be oxidised to form water.

hydrogen + oxygen  ==>   water

2h2(g)  + o2(g)  ==>   2h2o(l) 

your answer would be “dry”